Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
hello everybody!
i want to sample an analog signal with the board and send the 0/1 data with ble to the receiver .
i created my on service with rx and tx like in ble uart...
Hello Nordic Expert,
I am facing a stall pid issue with nRF52840 Dongle using nRF5_SDK_15.2.0_9412b96. The chip build code is QIAA C0 . I started with usbd_hid_generic example...
I have an application with Nordic devices as Central and Peripheral.
The first device is a multi-protocol device (nRF52840) and acts as BLE peripheral. Min connection interval...
Hello
System:
OS: Windows 10 x64
Application: nRF Connect 2.6.1 (with Bluetooth Low Energy 2.2.0 and Programmer 1.0.2)
Problem:
My device is connected to the COM7...
Hi,
I currently have a custom board with an nRF51422 on board. I am considering upgrading to the nRF52 series. Are there any nRF52 models that are pin compatible that I...
Hello,
We are working on a network of low energy sensors that work without connection. The sensors have a configurable service, so from time to time it makes itself available...
Hi,
I'm trying to implement Buttonless DFU into an existing BLE application. I'm using nRF52832 V1.1.0 boards (one for the BLE peripheral running the application and buttonless...
currently i am running ble_app_uart_c example from sdk15.0 and i successfully discover one of the custom service.now i want to discover all the services provided by peripheral...
What is the output for the capacitive sense driver example? ADC code? Voltage? Time? For example, when the csense_handler function is called, the following line will print...
Hi I'm facing problem to detect external crystal oscillator in my custom nrf52832 board's. I'm think it is not connection issue as I'm facing same issue in other 9 boards...
Hello, everybody.
I'm working on combining the nRF52840 and the GPS module and are currently developing a program that stores real-time GPS data in an external flash memory...
Hi,
We are planning on upgrading the firmware on our device from Mesh v0.9.2 to Mesh v3.0.0 via BLE.
Specifically, our current stack uses: - nRF5 SDK for Mesh v0.9.2 ...
IPhoneX sometimes goes into the ble_evt_handler auth_status event, and then p_ble_evt->evt.gap_evt.params. Auth_status.auth_status!= BLE_GAP_SEC_STATUS_SUCCESS, other iPhone...
I am unable to compile any SDK12 example with SES even following the tutorials. Versions in tutorials are different from those actually available resulting that menus shown...
