Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Question about usage. I am using the nRF52, and ported product code that was running on the Alpha SDK11 to the release SDK11. I believe that what I will describe is a new...
According to the product specification of the nRF51422 the current between the advertisements is:
i_sleep = I_on + I_rtc + I_x32k
16k Ram enabled: = 2,6 µA + 0,1 µA...
I realize that this code is "experimental", but we are trying to utilize it as a reference and having problems with its stability and scan results.
Specifically, we are...
Hi!
We are currently implementing a time synchronization algorithm using a nRF52s. Currently, we´re getting the min error of 20ms between synchronized slaves. We think that...
I'm using a nRF51 with 32K RAM and SD120. When I started using RTT Viewer I could send data to the terminal, and debug my code. Recently my J-Link plus won't allow me to debug...
I'm trying to secure my peripheral by allowing only bonded devices to connect. I'm using device manager, when I bond a central with nrf master control, the bonding succeed...
Hi,
I'm facing the following issue when trying to use the DFU bootloader. Below you can find the code of the bootloader, which I flash after I erase everything, flash S110...
hii....
i want to make my device connected through a secret pass code (may be six digit)..ie. my device get advertise then when master control panel discover my device...
Hello,
I was just wondering what are the steps to download my software that I made to nRF51422 to the nRF51822. I changed the target device and the memory areas in the...
Hi,
I am using SD 120 9.1.0 and SDK 8 as a central and SD 110 V8.0.0 and SDK 8 as a peripheral.
I have a setup central connects with 8 peripherals. First I had 1 central...
Hi guys,
I'm wondering what is written there in "empty section" between 0x7c0 and 0x1000 address? Are there any special registers (which must not be overwritten)? It looks...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello everyone,
I want to know if it is possible and how to show advertising data on display lcd (20x4 or graphic lcd). I'm using PCA10028 board with S120 and Nokia5110 LCD...
Hello,
I have read through the pstorage documentation here: devzone.nordicsemi.com/.../a00018.html
and I followed the tutorial here:
devzone.nordicsemi.com/.../
...
I created a bsp folder dfu_dual_bank_serial_s120 from PCA10028/dfu_dual_bak_serial_s13 in examples/dfu/bootloader/PCA10028.
This is for supporting DFU over UART for our...
