Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello, I'm working with NCS 2.6.0 in Visual Studio Code.
When I execute the code in my project, I receive error messages before the main loop starts.
I think there's some...
From what I understand, when A-GPS data is acquired using the GNSS-sample it is automatically stored in the NVS-memory of the modem? If the system acquires A-GPS data and...
Hello,
Project secure boot loader S140, SDK 16.0, nRF52840.
This line of code causes compile/LInker errors in my project. I guess I need to adjust memory start address...
Hello,
my application is running without TF-M and I store a password persistently in trusted memory using "psa_import_key()". This works with SDK 2.4.2. After that I made...
Good day! I have a nRF52840 based board that I interfaced with a MEMS microphone (SPH0645) through I2S interfacing. I got to the point where sounds made near the microphone...
Hi, I am developing on NRF5340 chip, using an external Flash memory (AT25SL321) on my custom board. I was previously using vanilla Zephyr version 3.1.0 (everything was working...
Hello，
Why is this error displayed?
00> <error> ble_scan: sd_ble_gap_scan_start returned 0x7 00> 00> <error> app: Fatal error
I use the example in nRF5_SDK_17.1.0_ddde560...
hi，
I want to know how Bluetooth allocates channel resources as a master.
Assuming a Bluetooth master is connected to 8 slaves simultaneously, how does the master allocate...
I am working on a module MS12SF1 which is nrf5340+nrf7002. I set the mac address in the otp by running wifi_radio_ficr_prog otp_write_params command. After restarting the...
On SDK 17.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and...
Hello,
The following error occurred when I ran the program. 00> <info> peer_manager_handler: Connection security failed: role: Central, conn_handle: 0x0, procedure: Encryption...
Now using 52840(S140_nrf52_7.2.0 protocol stack, SDK:17.1.0) Bluetooth packet sending found that the packet sending data length is far less than the actual length to be sent...
I am using a module named MS12SF1 which is a nrf7002+nrf5340 combine module. For wifi initialization, qspi is used. As it wasn't working I added spi4 in the nrf5340dk_nrf5340_cpuapp...
Hi Support Team
If we use nRF52840 develop BLE peripheral base on NCS. What is the maximum number of phones can connect nRF52840 at the same time? Many thanks.
Hello, I'm working on the nrf7002dk WiFi station sample. Most of the time, data is sent and received successfully through HTTP using the HTTP PUT function. However, occasionally...
