I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello everyone, I have successfully implemented the light Switch examples in the Mesh SDK. I sent the on_off data from the switch device to the light device. But what I need...
Hi All,
I’m running a proprietary RF protocol on an nRF52832 and am seeing some corruption of data when it passes through the CCM. The first byte is the only data that is...
Hi Devzone,
I know that more specific information is needed (time interval, Tx power, data length, ....) to make a comparison between GAP and GATT. But in general, which...
I'm working with following project and would like to add the DFU trigger library.
https://github.com/openthread/ot-nrf528xx
1. Build like this, I'm using a PCA10059 Dongle...
Hello,
I am working with nrf5281 and its bluetooth connection, the connection is established well and the chip and the nrf connect application stay connected, however the...
Hi,
I recently installed nRF Connect SDK v1.6.0 through the Toolchain Manager of nRF Connect. Previously v1.5.0 was installed, and was what I have been developing using...
I am trying to implement the buttonless dfu example, I successfully managed to upload the template example examples\ble_peripheral\ble_app_buttonless_dfu and can see it advertising...
Hi all,
I'm working on a limited power budget system. MSP430 is the master that is supplying power to nrf51882 (slave). Every 2s MSP430 derives a pin high to drive the nrf51...
nrf9160 modem Firmware version 1.3.0 release listed nidd or non-ip support. in the firmware.
We are eager to use this feature to send/receive data over RF control plane...
"CTE can be used in both connectionless and connection-oriented scenarios. For connectionless use, the periodic advertising feature is required (since deterministic timing...
Hello all,
I'm using NRF52840 with last sdk (V1.6.0) of nrf connect but I can't put the device into sleep mode (where the current consumption is at about 3/4 U) the device...
Hi,
I need a 1Hz clock with its interrupt function.
Where do I find an example to set the timer RTC0 or RTC1 to 1Hz and how to set the timer callback function?
Thanks...
Hi,
I am using nrfx_twim driver, and I want to read value from sensor's register. When I want to do that sequence looks something like this:
(SENSOR_I2c_ADDR+Read_bit...
Hello Sirs
I have two questions about the nrf5340-dk evaluation board.
The first one is how can I get the scan data of an advertising device?
And the second is that...
