Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
how to configure S112 for maximum throught put just like ATT_MTU Throughput Example available for other soft device. I tried everything on nRF52810 using S112 and the max...
Hi, I am using PTS 7.0 for Bluetooth profiles testing. The DUT is connected to PC (with Ubuntu and Android AOSP system installed). The Android PTS test instruction indicates...
Hi,
I am having some problems with nrfutil. I encountered the following errors when trying to generate a key. Similar issue was seen when trying to generate a zip file....
Hi,
I have a code word well in nRF52832 used twis1.I transplant it from nRF52832 to 52810.First I enabled twis0,Second, change NRF_DRV_TWIS_INSTANCE to twis0.Then I can...
Hello!
nRF52832, SDK15, SES
I'm working on a project where DFU is activated by receiving a command from the app. I took ble_app_buttonless_dfu as reference.
For starters...
Hi,
I am using SDK14.2, s132, with nRF Connect on Android.
I have used my own implementation of the CTS_C BLE service. The chip is able to detect, and request the...
Nordic Semiconductor-ites and fellow forum members have yet to steer me wrong so here we go.
My product has 52832 on both sides. The central and its 21col x 2 row LCD display...
Hello,
I am developing an application with SDK 15.2 on my nRF52840 development board (pca10056) and want to run it on my nRF52840 dongle (pca10059). I have hit a problem...
We have been comparing the current consumption of the nRF52 running FreeRTOS Tickless Idle versus a constant tick and using the idle task to sleep and the results are interesting...
Hi,
Does the pc_ble_driver_py contain any API for paring or bonding bluetooth devices? And if so, do you have any examples or documentation which explain how to use them...
Hi,
Is there a way to reject a buttonless DFU attempt (nRF52832, SDK14.2) ?
I want my application to allow DFU only when certain conditions are met.
I thought using...
Hi,
Can anybody clear me on the maximum and minimum connection interval with some good example. I have not understood the connection intervals clearly.
Regards,
An...
I am working on a BT mesh network where nodes are mostly sleeping (to conserve power) when they wake up, they need to send a sensor reading to another node (which is always...
It is unclear for me why the following code look like this (conn_ble_gap_sec_keys.c, SDK15):
Is it logical that here the SER_MAX_ADV_DATA is used? is there actual advertising...
Hi , nrf connect V.2.5.0 in windows 10 64bit, fails to launch Bluetooth low energy app. "DEBUG UART read operation on port aborted" is the log info which i came to know from...
