Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi,
I have been working through the examples for DFU with the nrf52832 dev kits from the SDK (nRF5_SDK_15.0.0_a53641a) from this folder:
...\nRF5_SDK_15.0.0_a53641a\examples...
Hi, Guys, I have problem with my nRF51822. I built the ble_app_uart project in the SDK v6 and and flashed it on the mcu using j-link and I also flashed S110 SoftDevice version...
Hi Sirs:
I've searched 52840 specifications and devzone, but there is no related information about the maximum external flash size could be adopted on 52840.
Would you...
I'm attempting to use PPI and Timer2 on the NRF52810 to count the clock pulses coming out of the SPIM driver. As there is no way to do this internally (as far as I know) I...
Hi,
I'm using a nrf52 as pheripheral BLE in embedded system with sensors. I need a ble central to receive the data from the sensors by connecting to the nrf52. I'm trying...
Hello, i am trying to store a lot of informations in the flash in order to do this i separated my data in several arrays. I want to store all my arrays in with the same file_ID...
In our project, two RF modules (with nRF24L01+ IC) are used in communicating data. If there is no WiFi around, the two RF modules can communicate very well without packet...
Hi everyone,
I found this example in the SDK for the nRF52840 Dongle: nRF5_SDK_15.0.0_a53641a\examples\connectivity\ble_connectivity\pca10059\ser_s140_usb_hci.
With this...
Dear Sr.,
Can't detect carrier
They are two PCB one TX Carrier and other mush Detect the carrier ---------------------------------------------------------------------...
mains.c
Hello Everyone,
I have deveLoped the Custom PCB whixh has the push button which is connected to VCC so i would like verify my software logic for button configuration...
Hi,
We have a new product based on the NRF52840. We are trying to add NFC record text to the firmware that based on SDK15. We could get the NFC record text from the NRF52840...
We're evaluating the nrf52840 and I am looking at the SPIM peripheral. The datasheet states the following:
"If several AHB bus masters try to access the same AHB slave at...
i am working on the Cycling Speed and Cadence sensor central configuration using nRF52832 DK in Segger Embedded Studio. I used the RSCS central example of nrf_sdk_v15.0 and...
I'm trying to migrate a working application from SDK 14.0.0 to SDK 14.2.0. I was using app_twi on SDK 14.0.0 and am now using nrf_twi_mngr on SDK 14.2.0. One difference is...
