I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Recently we are purchased nRf51dk and nRfbeacon boards for FOTA function but both boards are not working, we already followed the follwoing links:
1. developer.mbed.org...
Hi nordic engineers,
I want to add a mouse function in the keyboard application project, but have some questions to know:
1.Does BLE support such compositive device...
Hi,
I am new to the BLE and Soft device stack, I am working on Multi link peripheral example with SDK version 9.0. I have flashed the S110_nRF51_8.0.0 into the nRF51-DK...
I wanna to make an iBeacon device based on ble_app_beacon example.
I found in the example the default advertising mode is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND, where its advertising...
Hi all,
I just received my nRF52 DK and started attempting to run examples on it. I am having an odd trouble that the LED2 is always lit after programming the board, no...
Hello,
I ran PCA10005 board with nrf51-ble-app-lbs application and programmed PCA10004 with S120 ble_app_multilink_central. I have connection between them (I just changed...
Hello everybody,
I am currently experimenting with BLE on the nRF51-Ek. At measurement on the oscilloscope, the BLE protocol shows a behavior that I do not quite understand...
Hello.
I get error 0x10 (error for invalid flags) when i want to write to peripheral with my master module. I use the same code i always used, and i didnt change anything...
Hello.
I written code for nRF51822 w/ MPU6050 in S110(8.0.0) and Keil.
I tried to setup gyro as bellow.
twi_master_init(); => mpu6050_init(MOTION_SENSOR_ADDRESS);...
Hello
I have connected the nrF51-DK board and it was recognized by the computer.
I have managed to put in in a boot loader mode.
Since I switched it to boot loader...
I have three pca10001 boards. One is programmed as multilink central and other is programmed as multilink peripheral. when both peripherals are connected to central, the central...
I'm a newbie for Nordic development.
I just noticed that softdevice, app, and bootloader share the same CPU, RAM and Flash at the same time. This three software modules...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
Hi
I use an avr attiny441 with the nRF24AP2. Communication is over SPI byte flow. After start up, I get the start-up-message from nRF24AP2. That's fine. Afterwards, when...
