Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I have a question regarding the SAADC timing parameters.
I could not find an official specification for the SAADC power-up time (t_PWRUP). While measuring it on my...
Hi,
I am using bare metal SDK v2.0.0 and am trying to build the fuel gauge sample inside nrf-bm\v2.0.0\nrf\samples\pmic\native\npm13xx_fuel_gauge. I am using bm_nrf54l15dk...
nRF9160 - mfw 1.3.7 - NCS 3.2.4 In my experience, DNS lookup fails with some SIM cards using cloudflare as primary DNS. I wrote to the SIM card provider about that issue and...
Hello, we are having issues with using the nrf9151DK as a programmer for our own custom nrf9151 board. As the board seems to be locked, we tried to unlock it using the nrfutil...
Dear support,
We are connecting with an MQTT server with an expired server certificate. My expectation is that the handshake fails, but apparently the NRF9161 accepts the...
Hello.
We are developing a project based on the nRF54L15 SoC, utilizing MCUboot, image compression, and TF-M (Trusted Firmware-M). As part of our upgrade from NCS v3.2.4...
Hi Nordic support:
We previously submitted a case about OTA testing in CMW500 connection mode. Following is that case:
We tried OTA testing with the CMW500 connection...
Hi!
Im creating my own custom board based on the nrf54l15dk board included in zephyr. My board uses both cpuapp and cpuflpr, and has a custom partitioning scheme defined...
Hi Asbjørn，
As I mentioned in case 352770
We are in same question as the initial question issued by our colleague RongLinQin. As I mentioned, we want to conduct BLE OTA...
Hello support!
I am using the nRF9151 and the nPM1300 on a custom board.
Is is possible to measure the current drawn by the board via the VBUSIN? The reason is too have...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hi
I'm encountering a problem than the ANT device cannot be scanned. you can use project "ble_ant_app_hrm_v324"(ncs 324）, and modify "
light_rx_open_head" to connect...
Hi.
Environment : nrf52833, ncs v3.1.1
I am developing device that has PAwR Scanner Role and Extended Advertising for connecting Mobile Phone(nRF Connect APP).
PAwR...
I am using nRF52840 as host processor. Now I need to connect to nRF7002 for WiFi usage. I am using ncs 2.2.2 SDK. I have a few questions? 1. Does nRF7002 work on v2.2.2? I...
