I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello,
I'm a relative neophyte when it comes to non-hardware aspects of WiFi ICs, so I have some basic questions about the nRF7002; these are features my client is asking...
Hello!
I am new to the nRF52840 Dongle and Kali Linux running on a Pi 4B. Can someone point me to a source to walk a newbie through the install process? Any help is greatly...
Hi
at embedded world nordic presented a camera demo similar to this:
https://www.youtube.com/watch?v=mkYzTxRO1-w
Where can I find the repo for that (app and firmware...
Hi, I am using the nrf-dm sample with the nrf52840dk to measure the distance between two boards, but I am getting inaccuracte results. At a distance of about 60 centimeters...
We are currently thinking about implementing LE-Audio in CIS mode by reusing the sample program nRF5340_Adudio.
There are two types of boards to create: a transceiver board...
Hello everyone,
I've successfully implemented the SLM example on the NRF9160, and it's functioning properly. Now, I'm attempting to send AT commands to the modem using my...
what should i do to get the what should i do to get the thingy91 connected to LTE Network ? the SIM has been acitvited but i still cannot connect the Dk to the network.thingy91...
Hi, I am working with ncs 2.6.0 trying to implement some logs using the DiagnosticLogs cluster
But It looks to me like it is not impemented/supported yet.
For testing...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
I am using the Direct Test Mode sample as a starting point (samples\bluetooth\direct_test_mode). I am using NRF Connect SDK Toolchain v2.5.0 and NRF Connect SDK v2.5.0. I...
As far as I know, ppk2 is an eye-catching and open source power evaluation tool. I got the source code of the power profiler from github, and obtained the hardware design...
Hello,
With the CMakeLists file, is it possible to make an error during compilation if the SDK version is not the correct one?
Example: I am developing an application...
I'm trying to modify this bit-banging ws2812 gpio Zephy driver to run on an nrf9160 board. The problem is I can't mange to get consistent pulse timing using assembly instructions...
