Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hello nordic. I have several SPI peripherals connected to the nRF9160. I'm using the PPK2 in ampere mode. Does this then also measure the additional current drawn by the SPI...
Hello,
I'm wrapping up the layout of a board based on the NRF52832 (DCDC). I've tried to replicate the reference design as close as possible. I'm using Kicad and had to...
Hi,
Referring to the case,
https://devzone.nordicsemi.com/f/nordic-q-a/72660/nrf-connect-sdk-v-1-5-0-how-where-to-change-phy-and-tx-power-for-long-range-application
...
Code is based on Nordic UART Service Client sample on nRF Connect SDK v1.8.0
I am trying to create several client connections for different servers. The code is incomplete...
Hi Nordic team
I tried SDK Connect v1.8.0 ble_peripheral_lbs_coex sample.
It found advertising signal was very weak. The distance between PCA10112 and my phone was 1 meter...
I use PPI for ADC and GPIO pulling. When I connect and then disconnect - nrf52840 not advertise until reset the SoC.
I can connect after reset. But when I disconect then...
I am used to using Segger, but am switching to west for various reasons. The main reason is to create a CI/CD pipeline.
I built a sample project with west, didn't see any...
Hello,
I am new to embedded/BLE development so forgive me for my ignorance on some of these topics. I am creating a fairly simple BLE Peripheral Server device that has a...
I have built and run the application: Asset Tracker v2 using Segger IDE with nRF Connect SDK 1.8.0 , and my nRF9160DK device communicates with the AWS IoT Core topics.
I...
Hello Team,
I have interfaced Oled with NRF52805 on i2C.
I have used SDK 15.1.0. and ble_app_uart example [s112].
My problem :
I have made some customized functions...
Hi everyone,
I'm using SEGGER Studio for development. I wrote a code for accessing Flash memory by modifying flshawrite example in SDK.
Now I want to copy all dependencies...
hi,
How can I access flash memory of nRF52840 while using softdevice ? I just want to read and update two integer values? is there any simple way to do this?
Thank you...
Hi all:
I want to dynamically change device_name at peripheral_hids_mouse,
I perform two tests, but they are all not successful.
(1)
add below command into prj.conf...
Hello,
I am attempting to configure a Raspberry Pi as an OpenThread router, using the nRF52840DK for the RCP. Everything built fine. When the Raspberry Pi boots the avahi...
