Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
How interrupt is working in nrf saac driver? I can see that it is already code is present in the adc_nrf_saac.c
static int init_saadc ( const struct device...
Hello,
I was wondering if it is possible to port older projects built using the now deprecated Nordic Thingy:52 SDK ( https://github.com/NordicSemiconductor/Nordic-Thingy52...
Hi,
As a university we bought several NRF51422 dongles to sniff BLE traffic
Following the installation instruction here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hello,
I am new in nordic previously I was working on Cypress controllers. I am trying to put the device in System ON Low power mode.
I have tried the below functions...
Hi,
I am working on a project using BT Mesh and I am evaluating a prototype using the nrf52840. I am not working with the mesh-SDK, because I am using zephyr. I am working...
Hi, I have a University group project which required us to build software on Android devices. Basically, this project requires us to build software based on BLE Mesh between...
Hello,
I want to communicate one card nrf5340dk with 2 same card in using 'central_uart' and 'peripheral_uart' samples.
I have succeeded to establish the connection and...
Hi,
We have a new product and are looking into OOB pairing for authentication and encryption. All the information about OOB flows back to NFC pairing, but that is not what...
Hi
I am working on an application that uses extended periodic advertising feature of BLE 5. In this sample (periodic sync):
https://github.com/nrfconnect/sdk-zephyr...
Hello nordic. I have several SPI peripherals connected to the nRF9160. I'm using the PPK2 in ampere mode. Does this then also measure the additional current drawn by the SPI...
Hello,
I'm wrapping up the layout of a board based on the NRF52832 (DCDC). I've tried to replicate the reference design as close as possible. I'm using Kicad and had to...
Hi,
Referring to the case,
https://devzone.nordicsemi.com/f/nordic-q-a/72660/nrf-connect-sdk-v-1-5-0-how-where-to-change-phy-and-tx-power-for-long-range-application
...
Code is based on Nordic UART Service Client sample on nRF Connect SDK v1.8.0
I am trying to create several client connections for different servers. The code is incomplete...
Hi Nordic team
I tried SDK Connect v1.8.0 ble_peripheral_lbs_coex sample.
It found advertising signal was very weak. The distance between PCA10112 and my phone was 1 meter...
