I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
I found that when my custom board spend 201 ms to boot up. Because I can't change my board, I am looking for reducing time to boot up.
Do you have any idea and how...
Can you please tell me why I get an -ENOTSUP error when I set the scan .timeout parameter to anything but 0? Is the suggested workaround to use RTOS functionality to timeout...
Hello All,
I have the following issue - a peripheral and a central using nrf52832 with SDK 15.3 and S132 - on the peripheral I advertise with a whitelist - the central scans...
nRF Connect used to work fine. After the 3.8 update it could no longer see devices. At that point a re-install helped.
Then after the 3.9 update it stopped working again...
Dear support,
I am using nRF52840DK (PCA10056) and nRF5 SDK version: nRF5_SDK_17.0.2_d674dde. I am trying to make all the prints in my application to be displayed properly...
I working with the MDBT42Q-DB with the nRF52805 module. I've started from the ble_app_beacon example in SDK 17.1.0. I was able to compile and run the example in Segger Studio...
Hi.
I used sdk 1.4.0 with nrf9160, I used UART2 to comunicate with another mcu. I run fine and no problem.
Today, I update to SDK 1.6.0, I edited UART2 ( in device tree...
The RTC irq_handler of the latest nRF5 SDK may cause potential problems.
Imagine someone trying to extend the RTC timer from 24bit to 32bit, the developer has to keep an...
Hi All，
The version of Wireshark I used is 3.4.0.
The version of Python I used is 3.6.7.
Packet capture device uses nrf52840 chip.
After installing Wirkshark and related...
I'm working on nrf5340 DK and I wanted to use a mic for sound detection. To do so I installed the X-nucleo-IKS02A1 shield on my board because I have seen that it is compatible...
Hi - I'm using a nRF52840 DK for the first time with my 2010 MacBook pro running OSX Sierra version 10.12.6. I have SEGGER Embedded Studio for ARM 4.12 installed and Segger...
Sometimes, the output of the NRF_LOG commands does not make it to the RTT viewer.
The output of such commands as NRF_LOG_INFO() and NRF_LOG_DEBUG() and NRF_LOG_HEXDUMP_DEBUG...
I design with reference to the evaluation board (nRF9160-DK). What kind of resistor (R4) is used for the input circuit of the GPS antenna? The manufacturer and part number...
Hello,
In the past months, I'm being developing Zigbee Routers-based applications and so far everything is going well.
I've already a few devices installed without OTA...
