Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
nRF52840 works with 1.8V supply voltage? We are using Circuit configuration number.5. it tells VDD should connect to VDDH.
As per the circuit configuration 5: VDDH is N...
Hi :
we met some quesiton when using nRF52840:
1. Is it possible to drive a pin to high or low in sleep mode? For eg. we would like to put pin P0.12(may be other pins...
I am trying to communicate between an ADXL362 accelerometer and a nRF9160 DK. I see on this link https://docs.zephyrproject.org/latest/samples/sensor/adxl362/README.html that...
Hello
we had purchased nRF6700 and nRF24LE1-F16Q24-DK from Mouser India on 14-oct-19 .and it comes with an older version of firmware i.e.(3743) And currently, I am facing...
Hello:
I have to nRF52DK boards and I am able to run the ligth_switch example, but the thing that I want to do is send a message, "hello" from one node to other. I saw...
Sir in the above code i have a cmd_zb_match_desc() but i am calling inside the switch case but after calling i didn't able going inside the finction
please give the Suggestion...
HI,
I want to send heart rate data to smartphone using NRF51422 in every second without any time delay or minimal time delay ranges between(0.9 to 1.1 sec).
Thanks...
Hello,
I managed to get a central application to run on the nRF52810 with SDK 14.2 and S132 V5.1.0. I also got the bootloader working with this setup.
Right now I'm having...
Hi!
I have nrf52 periperial mode, SDK15, s132.
I connect a smartphon in the central mode to my nRF52 and start to send some data.
In the nRF52 I receive those data in...
Hi, I am trying to print double/float values, but Its printing blank. e.g. printk(" value:%.3f\n", value); output: value:%.3f printk(" value:%lf\n", value); output: value...
My project consists of reading an NFC card's value (using another chip), and respond to the interrupt generated by that chip to read the value from it using SPI. Then, this...
Currently I am using VS Code for development. Mostly everything is fine and VS code is awesome.
However there are some problems I am facing.
1. It is time consuming to...
Hi,
In my application,for the first time device (nrf52832)will start advertising and on nrfconnect for mobile application side we make it get connected and bonded.It may...
Hello! I'm trying to develop an Android-nRF-Toolbox App. What features and folders do i use with show logs? In order to develop the uart in the toolbox app, we have deleted...
