Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
for 52840, customer want to have a part of flash, it can set write protect, to avoid illegal erase or destroy, they use this part of flash to run boot-loader, is it passable...
As far as I could see, only GGA NMEA sentences are enabled by default. I want to check if RMC sentences deliver positions faster, and in my prj.conf I do the following:
...
I got an nRF52 DK and I was unable to recognize the JLINK driver by connecting to my computer via USB. My SEGGER version is 6.44E and my own jlinkV9 is normal. How can I solve...
hi all ,
now , i need add create mqtt ble gateway .
it compiler failed follow message :
C:/temp/ncs/zephyr/drivers/serial/uart_nrfx_uarte.c:1272:9: error: 'DT_NORDIC_NRF_UARTE_UART_2_LABEL...
I am playing with flash and fstorage lib. I finally got it up and running - I can write and read to flash without having fatal errors. But it's not working as expected. I...
Hi all,
I am running in a strange problem. I am using the gfx example under peripheral with the nRF52840 DK and a display with ST7735 driver. I connected the display to...
Hi,
I am looking for the C# library for the development of Windows PC applications to communicate with nRF52 Bluetooth module.
Is there any C# library available to...
Hello,
I work with an nRF52840 DK and I want to put together the "Light switch" application with the "BLE_app_uart" application . I use the S140 softdevice, SDK 15.3.0 and...
I was looking at the specifications of a n52840 and was curious in how much power is consumed from the Analog to Digital converter in the nR52840 during the conversion. I...
Dear Nordic Support,
I am using PPI to link 2 timers (10ms & 5s) with 2 SAADC channel (AIN1 - channel 0 & AIN2 - channel 1).
The nrf_drv_saadc_init function is only called...
sdk15, SES, SD132 Hi I am using an SPI slave with nrf52 (master) I launch in the main() and I also initialize the SPI slave on main. I also configured an app timer and when...
[EDIT] The solution is posted in one of my replies.
I'd like to set up a programming and test station for the nRF52832. Segger JLink tools work fine in Windows, but I...
Good day Nordic,
I am starting to work over the ble_uart_central example, this is a project that uses bsp_event_handler to issue the events from buttons, but I cannot...
