Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi, all
i have using adxl335 sensor interfacing ADC ;i have done code ,i wanted to know is it correct or the way i have developed the code can any one suggest me.
How...
Hey guys,
I have followed this tutorial that shows how to modify advertising data, and more particularly the name.
What I want to do is set a name in the beacon example...
I've added a HID service in my project.
I see a lot of messages
<00> debug> nrf_sdh_ble: BLE event: 0x57.
in the RTT Viewer.
What does the event 0x57 mean?
Hello All,
We are designing a product based on Tracking device, for this we use nRF9160 module & use controller #nRF52840 to send AT command for LTE and GPS.
We do not...
I'm trying to track down an issue where our application gets stuck due to what looks like an infinite loop in the app_timer2 timer list. When it occurs we see the next pointer...
Hello,
I'm using a custom board with nrf52 using sdk12.1 and SD132 v3.0.0. and the nordic's nus peripheral service.
I am able able to read and send data without any...
Hi,
I had a building project until I added app_uart_fifo.c. The app fifo and uart flags are enabled in the sdk_config.h. This is a custom board. Now when I build I get the...
Hi, I'm building a BLE peripheral with one button only. The button exposed over bluetooth. Obviously, the button handling module (GPIOTE) is used. After advertisement timeout...
Hi,
I am want to do wake up on motion when any threshold value generated by icm 20948 accelerometer I want to send an interrupt from icm 20948 to nrf52832 to wake up from...
Hi !
I'm using the nrf52832 with SDK 11 as pheripheral.
In Android phone the bonding and the scan request working great with my unit !
However, in IOS
1) i do scan...
Hello,
I am working with LPN example of SDK 3.1.0. In the example I need to change the poll interval time based on our application requirement.
I looked at this equation...
Hi Nordic team,
I have a curious problem I need a little help with:
(NRF52840 & SDK 15.3)
I have a project which is an integration of the ble_uart example and the serial_uartes...
I have searched your forum and have found several references to my issue; however, I have not been able to get anything resolved.
I am using the nRF51822 which is part of...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I have gone through “Application Timer” tutorial...
I have a development board and load the client central BLE blinky to it, then the peripheral BLE blinky to my custom board and power up and the central development board stays...
