Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
Hi, I am using custom board with nRF52832 and nfc. I am using SDK15.2.0 and Softdevice S132 v6.1.0 to advertising packets . I have referred examples\nfc\\record_text...
I would like to know the best place to cut the power in switch off sequence.
We have a IO to totally cut power to the IC (own board), I added PIN control to switch off...
Hey,
I am currently using your product nRF52832 for RF Energy Harvesting applications. We need very low power consumption in sleep mode. In your user guide you mentioned...
Hello, when trying to finish provisioning my nodes (3 total, per example program's instructions), my provisioner program keeps running into
NRF_MESH_EVT_PROV_LINK_CLOSED...
i am using three boards , one is client (nrf52840) and other two boards as server(nRF52832) using light switch example . i want to get the message from client board ,to relay...
Hello,
I am having trouble understanding how the following function in the PWM driver example under peripherals in the SDK. Below is demo1 from the code that creates and...
I am not able to enter DFU Mode with secure bootloader example.
I use IAR and NRF Connect with Programmer to flash
Following are the steps I followed
1. Build Secure...
Hi Everyone,
In this code I'm face a problem. The issue is when i debug, it shows "<info> app: TWI device detected at address 0x6D" . Please find attached a snapshot of...
Hello,
I scrolled through some subjects about that SoC already but I wanted to get some more precision.
1. Can I start developing solutions for AoA / AoD system...
I am trying to do a ramping PWM. I want to update PWM every 25ms by increasing the duty cycle by 10%. I tried to setup a timer, by calling app_start_timer() on repeat mod...
Can you clarify how FLASH_SIZE, defined within the linker_section_placement_macros setting in the Segger Embedded Studio project file is used? Specifically: should it reflect...
In the light switch example, I try to change the network-key and then get some new unprovisioned servers provisioned.
The servers seem to get provisioned, but the client...
Hi,
I am working on NRF52840 preview DK using SDK version 15.3
I have compiled and loaded the Secure DFU bootloader onto the device, and also successfully got the BLE_BUTTONLESS_DFU...
I am using the mesh SDK version 2.2 (I think - I renamed the folder when I started, but I can't find a reference to the version number in the library! I am sure it is 2-point...
