Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi, I am working on SDK 15.0 Multilink central and Multi peripheral
Soft device: 6.0.0
Segger IDE
Application overview :
When the central request to all peripherals...
Hi, I have seen in other topics here that it is not possible to control the server of the light switch example from the Android App, only the Generic On Off Model. But when...
I am working on RTLS project using nrf52832 SOC. In beacon mode i want to advertise temperature and battery strength . but i am not sure if what method should i use to measure...
Hi,
I am using nrf51822 in my project.So we are using keil5 u vision project and sdk 12.3 version so here the problem is i have imported the example program from the sdk...
The nRF52840 supports 2 Master/Slave instances.
Is it possible to configure the nRF52840 as a Master when connected to an I2C bus that has another Master present?
SDK 15.2, S132 6.1, nRF52832
I have a characteristics to write data to a peripheral, using variable length up to 507 bytes and authorization.
Writing to the peripheral...
I'm using nrf_fstorage_wrile() which work fine on most of the cases, except for len == 6 bytes. When I read back on the Flash, after successful write, I found that only 6...
Hi,
It‘s great thing that the nRF9160 DK can buy.
But there are few question need to be confirmed?
1, I saw the "Onging ceretifications" ( https://www.nordicsemi.com...
Hi,
I am using a nRF9160 with the LTE-M modem firmware. But I want to change it to the NB-IoT firmware. I have followed the instructions to install the dfu.
But when I...
Hi
I am looking at the file
\examples\light_switch\server\light_switch_server_nrf52840_xxAA_s140_6_1_0.emProject
and in there I see that there is the line
linker_section_placements_segments...
Hi,
We are planning to develop an IOT device using the nRF52840 which will communicate with a Hub device which will contain another nRF52840 chip, so we want to check the...
Hello,
I am compiling with encryption implemented for Bluetooth communications. Specifically with code taken from the ble_app_hrs_c example.
I am seeing this error:
...
Hi Sir
I am testing nRF52840 product with CMW500 BT5.0 testing script. But the testing is easily stop due to connection broken, especially for RX and long range testing...
I made an application based on ble_app_uart example using s130_nrf51_2.0.1_softdevice.hex and I have 2 boards:
- 1 nrf51DK
- 1 target board using nRF51822-QFAA H0 (version...
