We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi, I have a few general questions on nus_data_send().
First off, is there another known way of transferring an array/string via ble to the Nordic mobile app other than...
Dear Sir,
I am working with nrf52832, SDK15 and s132 soft device.
I am using RIGADO DK .
Is it possible to continue advertising(from peripheral device) even after...
Hi All
I am doing a project which is base on SDK15.2 examples\proprietary_rf\gzll\gzp_dynamic_pairing\host\pca10040\blank\arm5_no_packs
I would like to add a timer to...
Hello,
I cannot add SPI0 to my application because OpenThread library was built with it without any interest of that. Could you fix it please ? (I need the 3 SPI peripherals...
Hello! I want to use the start time of the XOSC16M in NRF24LE1. I got ~4 ms. Can I put the processor to sleep at this time in standby mode? How to do it to wait for wakeup...
Hi all:
I see the "ant_share_channel _master_to_master" example,
this example is share_master,
my question is,
How to get p_ant_message[]?
the p_ant_message[]...
Is the recently released SoftDevice - ANT/BLE S332 SoftDevice v6.1.0 - compatible with the recently released SDK v15.2.0 ?
The supported SoftDevices listed in the documention...
Hello. A re-connection failure problem happens on our products.
chip:nRF52832 SoftDevice:S132 SDK v11.0
1. pairing and bonding on LESC 2. reset connection and re-connect...
Hi,
I have connected and SPI flash module to my pca10040 dev board. I wrote a test cycle of erase/write/verify for the entire flash and it works correctly. My initial pinout...
Hi,
I need some very simple file system to use on an external SPI flash. I gave a quick look at Flash Data Storage and it should be ok for me. I am not sure though why it...
Hi,
Disclaimer - this is definitely a question where one picture worth a 1000 words... ;)
My app use timeslot api to get a free time period to do some hard real-time...
Hello. How can I send binary data (in order to not convert it to ASCII string) over UART?
I have sensor data (obtained over BLE). Every measurement is 13 bytes, sample frequency...
Good day!
Thank you for your consideration of my problem! The system is an nRF52832 utilized as a motor driver of a small 2W high rpm maxon motor. The system performs as...
Hello,
I am trying to evaluate the nRF52 dev kit. The "getting started" HTML documentation has a link for "Setting up the development kit". This links loads "Oops (400)...
