Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi there, nRF52840-Preview-DK, 0.9.3 2017.43 nRF5_SDK_15.2.0_9412b96 IAR for ARM 7.60.1 Windows 10 Home Version 1803 OS build 17134.590
When I try to run secure_bootloader_usb_mbr_pca10056...
Hi,
In Mesh Profile v1.0 section 3.7.5.2 Acknowledged message one can read the following text.
"... If the acknowledged message has TTL set to 0, it is recommended that...
Hello,
I purchase nRF51822 Bluetooth Smart Beacon kit.
How to load the new program into this board.
I downloaded nRF51822 Bluetooth Smart Beacon kit firmware files...
Hi,
is there a simple way to enable serial logging instead of rtt in a mesh application for nrf52840DK, as example in the light switch server or client mesh applications...
On our custom board it can happen that an ASSERT triggers (suspect UART error due to EMC injection) on the connectivity chip, this meas that the application controller is...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor...
Hi,
I have an app that uses freeRTOS
My app runs OK , however when I am debugging it in segger studio with my SWD connector, it crashes with no reason
If I check the...
Hi All,
(Segger IDE SES Ide version = 4.10)
Various posts have attempted this, some claiming success with the following tools command :-
"$(LINTDIR)\bin\pclp64...
I'm in the process of trying to port my SDK 14 project to SDK 15.2. I've made a pretty good amount of progress, but I have two issues that I can't seem to figure out.
The...
How do I find where else in the program pin 6 is being used and disable its other functionalities in the BLE_UART example?
I am trying to read data from a sensor via SPI...
Hi, I am a novice and need help to get stated with Segger and the nrf52DK. I have installed the latest SDK 15.2.0.
I have manage to run couple of exemple with no or only...
Hi,
I am using nRF52832 chip with SDK15 and S132 softdevice.
I want to change manufacturing data dynamically in advertising frame. I would like to know step for that with...
Hi all!
I've read that nRF9160 DK comes with modem configured as LTE-M.
At the moment in Spain, only have NB-IoT coverage so... how should we do to setup the nRF9160 as...
Hi,
I would like to obtain printf and NRF_LOG separately from two TX ports.
I made a test application of serial output based on blinky.
P0.06:TX (and P0.08:RX) were...
I'm working on the project where data from nRF52840 need to be send to Android over wire. The customer does not want to use BLE.
I can connect nRF52840-DK development board...
