Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi
Newbie in the nRF family of products so i might have missed the answers to my questions somewhere in the documentation and forum. if so i apologize.
I'm trying to get...
Hello ALL,
I have been using UART module and fstorage module in an application. I've been sending a bin file from PC to NRF52 using UART but when I tried to save it using...
Hi All,
I have some code that I'm porting from a Zilog platform over to the nRF52 platform. The code uses 1 timer and 1 uart. The goal of the code is to handle RS485 messages...
I am testing the IoT_lwip_MQTT_publisher_pca10056_s140 example project from SES on Windows.
I build and install the kernel with 6LoWPAN module on the Rpi3!
I can run from...
Hello，I'm from China。
At present, there is a need to broadcast beacon data in nrf51822 (SDK_12.3.0_d7731ad is used as the protocol stack version, and the...
Hi
I want to generate two PWM signals that are phase shifted with 90 degree, with similar duty cycle. I have the following pwm configuration, but I don't know how to proceed...
I am operating as a Central. How do I register and enable a discovered characteristic's indication?
I do the following and the subscribe passes but then the kernel crashes...
I'm planning to buy a nRF51822 based module for my BLE project & I wanted to know whether any of the nRF51822 based modules come with OTA ready bootloader out of the box....
Hi,
I'm trying to save sensor data to sd card on low power mode. When i connect to bluetooth mobile app can pull all data from sd card.
How can make this architecture...
Hi,
I'm using Nordic BLE Sniffer. When I look into the captured data I see a lot of malformed packet (CRC error). It try to decode any received data even if there is CRC...
I was digging around a bit in my code to get a better grip on logging. In sdk_config.h, I have the following relevant settings:
My modules all implement their own logging...
I am going to implement DFU over BLE in my nRF52832 project. Since the size of my application + softdevice larger than half my memory size I wonder how the update is performed...
We're looking to use the nRF91 to measure the LiPo battery voltage to determine battery health. We would want to know what the accuracy and range of %XVBAT is. Looking at...
I am trying to create CTS server using nRF 52840 dongle and nRF Connect PC app (v2.6.1). Currently I can manually provide current time and local time information to the app...
