Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I'm using the nRF52840 DK with the thread stack.
I want to test OTA but I only find documentation to do this via bluetooth.
Is there a way this can be done with Thread...
Sir,
In some examples I found some of the example programs does not contains Soft Device. What to do???
And when I Flashed the main file alone it shows some errors.
Hi,
When I look through the nRF52840 product spec I can see that SPIM0, SPIM1 and SPIM2 doesn't support speeds higher than 8Mbps.
Nothing is written about SPIM3 and it...
Hi there,
I am designing a bridge application between different devices which uses BLE as central and peripheral to connect all them, the idea is have up 20 nodes connected...
Hello
For a breadboard, we would like to duplicate the programmation part of the nRF52840 dev. kit.
Can you provide the layout of the dev. kit in electronic form (Mentor...
Hi,
I'm using nRF52832, nRF5 SDK 15.2 and Mesh SDK 3 .I have successfully integrated the UART module from nRF5 SDK / examples / peripheral /uart in the beaconing example...
Hi. I'm using nRF52832 with my external board. (SDK 15.0.0)
I want to merge UART, blinky and timer. I merged UART and timer example, and it worked.
Now, I want to merge...
Hi. I am tinkering with BLE settings, and changed NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 7.
I then get a 0x04 error code on this function after building and running the...
I have this project that I have been working on for sometime, however today I encountered this extremely weird error while building
I haven't changed any sort of project...
Hello! I'm using a module nrf51822 as a ble peripheral device.
And my device's RSSI is alway about -60db and the power comsumtion is 4mA.
Even i tried to change in sd_ble_gap_tx_power_set...
My application has a power button that pulls up to battery voltage (3.2-4.2V) to switch power into the system. It's also necessarily tied to a (heavily muxed) gpio pin with...
Hi
I have made a small Python script that generates a C-file with the build date/time and some other values.
Is it possible to make Segger Embedded Studio execute the...
Hi,
Is it possible to provide eagle design files (layout and schematic)? I see that you have provided for altium designer.
Also, is it possible to provide eagle library...
Looking for the best ways upgrading from a nRF5 SDK / SoftDevice based design to Zephyr. in my case, the nordic bootloader / upgrade process is configured for UART.
It would...
When using custom 128-bit base UUIDs and 16-bit UUIDs to address services or characteristics within the formerly specified base UUID, it seems the Nordic softdevices always...
