Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello everyone, I've followed the following guide for mesh dfu and had no issues with the example provided here : https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK...
Hello,
is it possible to set the sniffer/firmware to follow the central device instead of the peripheral?
Currently, only peripheral devices are shown in the device...
I'm attempting to get a grasp on how much CPU time an SAADC conversion is taking. I'm running the SAADC sample code from the nRF52 v15.1.0 SDK on an nRF52832. SAADC_CONFIG_RESOLUTION...
Hello everyone, We want to program the other NRF52832 chip from the NRF52832 chip via OTA. The DFU service UUID is 16 bits (0xfe59). However, the characteristic UUIDs are...
Hi,
I'm using the nrf5283 chip alongside with the SDK12.1. I have a strange situation related with the bootloader dfu.
First I flash with the programmer a merged hex...
Hello,
I'm working with Mesh SDK 3.1.0.
I made some changes in app_level.c file.
Could you please confirm that these changes are right?
They seem to work fine, but...
I am using SDK 15.2
I downloaded both nRF Toolbox and nRF Connect applications on my phone (Lenovo K6 which is running Android 7.0 but i tested the same thing on multiple...
Hi,
I'm attempting to flash program a Nina B112 Bluetooth Module (from Ublox), which is built uppon a NRF52832 board and i'm attaching this module to a custom board.
I...
Hello,
I'm building BLE preipheral and central devices for transmiting voice signal (best audio quality is not very important requirement) from peripheral to central. I...
Hi All,
We are in evaluation phase of a project where in our battery powered device would use nrF52840 MCU and communicate to the mobile phone over BLE (say about 5x times...
I am working on nrf52832 and sdk11. I want to store my accelerometer and gyroscope data into external memory.Does anyone have code of it? or any one having .c and .h file...
HI, I am using nrf52832 soc and i develop our own module. i need to create a mesh network within the device.
I am using segger embedded studio 3.34 (windows 10) and SDK...
I am new to BLE and want to learn what options and methods I have available to alter the advertisement package. Is it possible to include a floating point value, that could...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
