Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Are there any native RTOS build-in the SDK? If I need to develop a sensor device driver (i2c based) any recommendation as the safest way to do that. Choosing between freeRTOS...
Hi,
there is a broken link on https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/ble_sdk_app_buttonless_dfu that refers to " Generating bootloader settings...
I'm writing a production script that uses nrfutil to do OTA DFU for both nRF51 and nRF52 radios. I'm using a PCA10059 with nrfutil version 3.5.1.
It works fine for an nRF52...
Hello,
I am trying to use IAR examples to debug some of the examples provided in the SDK.
I am only using examples that support the pca10059 dongle.
One example is the...
Dear All and @rogerclark,
From the release note of nRF5 SDK v14.1.0, Segger Embedded Studio (SES 3.30) IDE has been supported originally.
I use MacOS, and I has set...
I need a help to create a mesh where two nrf52 dk are connectred in the mesh and one node sends a message and another node recives it and sends to a url
I am currently looking at how to put the nrf52 development board to sleep (and wake up) by sending a command from an android application (with SDK v15.2).
I have been experimenting...
Hi
I am trying to establish communication between a NRF24L01+ and an NRF51822, but unable to do so. I am able to communicate between 2 NRF24L01 + and also between 2 NRF51822...
Hello, I'm quite new to both the nRF52832 and the Segger Embedded Studio. I have a college project which involves I2C communication with 2 slaves. I was finally able to set...
Hello,
I am trying to read data from a sensor through sensor TX pin connected to RX pin of nrf51822. Nrf51822 recieves this data through RX pin and sends it via bluetooth...
I am seeing a problem using the nRF52 SAADC with two analog channels enabled in scan mode.
Essentially, channel 0 is measuring an analog signal with gain ~= 15 while channel...
Hello,
I am trying to get the RX interrupt to trigger on the PCA10001 board using the segger debugger as my serial terminal.
My hardware setup consists of a PCA10001...
SDK: v15 SoftDevice: S132 Chip: nRF52832 on BL652 Module
I have a command->response type system. The Central (Android phone) sends a command, and the Peripheral (nRF52 device...
Greetings!
I am using nRF52, SDK14.2, and NUS with MTU = 64. I want to transmit 1000 byte string over BLE upon reception of any character to "nus_data_handler" I have divided...
