Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello Nordic Expert,
I am facing a stall pid issue with nRF52840 Dongle using nRF5_SDK_15.2.0_9412b96. The chip build code is QIAA C0 . I started with usbd_hid_generic example...
I have an application with Nordic devices as Central and Peripheral.
The first device is a multi-protocol device (nRF52840) and acts as BLE peripheral. Min connection interval...
Hello
System:
OS: Windows 10 x64
Application: nRF Connect 2.6.1 (with Bluetooth Low Energy 2.2.0 and Programmer 1.0.2)
Problem:
My device is connected to the COM7...
Hi,
I currently have a custom board with an nRF51422 on board. I am considering upgrading to the nRF52 series. Are there any nRF52 models that are pin compatible that I...
Hello,
We are working on a network of low energy sensors that work without connection. The sensors have a configurable service, so from time to time it makes itself available...
Hi,
I'm trying to implement Buttonless DFU into an existing BLE application. I'm using nRF52832 V1.1.0 boards (one for the BLE peripheral running the application and buttonless...
currently i am running ble_app_uart_c example from sdk15.0 and i successfully discover one of the custom service.now i want to discover all the services provided by peripheral...
What is the output for the capacitive sense driver example? ADC code? Voltage? Time? For example, when the csense_handler function is called, the following line will print...
Hi I'm facing problem to detect external crystal oscillator in my custom nrf52832 board's. I'm think it is not connection issue as I'm facing same issue in other 9 boards...
Hello, everybody.
I'm working on combining the nRF52840 and the GPS module and are currently developing a program that stores real-time GPS data in an external flash memory...
Hi,
We are planning on upgrading the firmware on our device from Mesh v0.9.2 to Mesh v3.0.0 via BLE.
Specifically, our current stack uses: - nRF5 SDK for Mesh v0.9.2 ...
IPhoneX sometimes goes into the ble_evt_handler auth_status event, and then p_ble_evt->evt.gap_evt.params. Auth_status.auth_status!= BLE_GAP_SEC_STATUS_SUCCESS, other iPhone...
I am unable to compile any SDK12 example with SES even following the tutorials. Versions in tutorials are different from those actually available resulting that menus shown...
What is the difference between the twi_sensor example and the twi_master_using_app_twi example? Where do I find any documentation that describes the available functions for...
