We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
What is the exact sequence when reading a characteristic with variable length and authorize required.
When I have a actual data length of 14 I can read with offset = 0 and...
Hi All Team Members,
Using Nordic Development Kit of nrf52832 I am able to write and test basic application using UART and BLE
using this kit I get the following error...
Hello, I use a custom board with nRF51822QFAA, with two buttons (left, right) and uart for printf/debug. The idea of the project is to have the board always sleeping, it wakes...
Hi,
I have a project which need to use two UART interface at the same time.
As well known, there only have one hardware UART interface in nRF51822/nRF52832. If I want...
Hello, DevZone,
I have programmed an nRF52-DK with the unmodified SDK's ble_app_hrs_pca10040_s132 (heart rate monitor) BLE peripheral application. I also have a Power Profiling...
Hi Susheel,
Thank you for your support.
We would like to get your advice related our new design, with the followings:
Assume we need to support besides of the BT5...
Hi,
I am developing one of the my project on custom board, in which I have to configured the two GPIO Pin's as input to sense the those pin and take actions assigned on...
I'm developing a battery powered BLE sensor application where I need some basic guidance on how to implement this:
The sensor action consists of a measurement process where...
Hi there!
I appreciate your work on Nordic SDKs which are getting better and better.
But sometimes SDK setup isn't as quick as it could be.
E.g. for evaluation purposes...
Hi,
I am trying to port the Thingy project (ble_app_thingy_s132_pca20020) to Segger Embedded Studio on a Mac and it proved to be not an easy task, in fact I have hit a...
Dear all, I am building a BLE thermometer based on nRF51422 chip. I need to get certify it and if any of you performed and have the tests results of the below tests, for the...
The board came pre-programmed for MBED. I don't need that, wood like to enable regular JLink. I believe the process is to get it in boot loader update mode (hold boot/reset...
Hello,
I am new in this platform. Few days ago, my boss give me a nRFgo Motherboard. He want me to write a program that nRF24le1e can read/write data from sensor via I2C...
Just verifying to be 110% sure:
The TRACEDATA1-4 pins may be used as ordinary GPIO pins when no trace-functionality is configured for the debugger? So even if a debugger...
Hi,
I have a PCA10040 connected with some wires to an external I2C device and I need to poll data from the I2C device and send it over BLE, also updating the advertisement...
