Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi everyone!
I want to work with two UART interfaces in my nRF52DK, in one hand, I must receive data sended by one cable which converts USB to serial, for this I use this...
Hello,
I caused a hardfault error and triggered the HardFault_Handler in "hardfault_handler_gcc.c". But instead seeint its source, I could only see the message no source...
When I start the nRF51822 sniffer ble-sniffer_win_1.0.1_1111_Sniffer.exe I get the following message:
!!Your firmware is outdated!!
Please upgrade (press CTRL-R).
When...
Hi team,
I am using sdk 12.1.0 and ble_app_hrs_c example.I enabled #define NRF_LOG_USES_TIMESTAMP 0 to 1 and iam usng nrf51822 dongle.my program gets hanged.I need to print...
Hi all,
I use the example of examples/ble_central/ble_app_multilink_central/ to test the connect timeout event. When it scan the peripheral and try to connect it, power off...
Hi, I am wondering why, sometimes, I get an odd packet out of order on the receiver. It is very random, it can occur at anytime, though usually it takes a minute or two. Testing...
So, does anyone have practical advice for reducing the code size of peer_manager and related modules, so that the ble_app_template project fits on the nrf51822 128KB part...
I am having an Windows 10 64bit OS. I am using PCA10000 board as sniffer. When i try to use it, I am getting Try plugging out the hardware error. Even CTRL +r is not working...
Hi
I have this board: www.sparkfun.com/.../13990 connected to a PCA10040 Nordic board. I am able to write and debug the Sparkfun board (the blinky LED example). I am now...
Hello,
According to the nRF Sniffer Guide 1.2, the sniffer is supported on a number of platforms (nRF51822/nRF51422 Evaluation Kits and others). All of them (as far as...
Hello,
I have problem when trying to use non default pins for uart.
This is what i got:
UART:WARNING:Function: nrf_drv_uart_init, error code: NRF_SUCCESS.
UART:INFO...
Hi,
Do you have any ready made example or can you give me guidance about the program in which the location is calucated based on RSSI values of the beacons.
Basically...
Hi,
I wanted to know that if I have e.g. 10 beacons placed in the super market. Let say I am in the meat section and there are three beacons among which I am close to one...
hi,
i'm designing a custom board and i want to detect when the USB is plugged in. the nrf51822 chip working with 2.5V, for that i had the idea to make a voltage divider...
Whenever I hit pair to pair the nrf51 dongle with the DK, I keep receiving the error line: Authentication failed with status BLE_GAP_SEC_STATUS_PAIRING_NOT_SUPP
I read...
