Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
my chip is nrf52833. In guide document , the XC1 and XC2 would connect to capacity. Both pin is used.
My project need one pin TCXO. which pin I should connect to? XC1 or...
Hi, everyone.
I am testing reading/writing data between n52840 and n9160 through UART with buf_len=1(byte by byte) based on Zephyr's UART_ASYNC_API provided in ncs v2.6...
I have an application that tries to configure pin 9 of port 0 on the nrf52840. this pin is reserved for NFC use. in one application it was enough to add:
& uicr {
nfct...
Hi ,
In NCS 2.8.0 the ESB-PTX sample how to config to achieve?
Now I had disable the UART log,after transmit 20 seconds I want to config the nRF54L15 into a low power...
There are 2 software: 1.0.1 and 1.0.2. When I load the 1.0.1 hex with bootloader with the programmer, it draws 9uA current. But when I update it to 1.0.2 with DFU, the current...
We are flashing the nRF52832 that works with DFU with a SoftDevice and a bootloader. The application code is compiled privately with a private key and packaged into a zip...
Hello Nordic Team,
We have a customer who needs to use the Nordic Distance Toolbox (NDT) functionality, and they are hoping to demonstrate it on the nRF54L15 DK. Is there...
Hello, I've tried to implement rtt logging in my own project but the control block cannot be found. So I tried the saadc example and that did not work either, I tried to use...
How do I use hardware crypto on a nRF9160dk? I am using the nRF connect SDK and my build is nrf9160dk_nrf9160_ns.
Would that be cryptocell or something else? If it's cryptocell...
I am using nRF52833 / NCS 2.8.0. I'm using Gazell Pairing, but I only need pairing, not encryption. So I'm only using unencrypted pipes. If it is a non-encrypted pipe, it...
Hi,
In my design, I have a push-button that pulls low when pressed and remains floating otherwise. This button is used to wake the nRF52832 from system off mode.
The push...
Hello nordic:
May I ask about the requirement of 32M OSC of 52832 ?
EX:
Frequency tolerance
Equivalent resistance
Loading capacitance
shunt capacitance
Drive...
