Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
HI
In the RF_Test example, there are 80 channels.
However, BLE has only 40 actual channels.
Why are there 40 channels...? I would like to know.
Do 80 channels...
Hi,
I am new to the NRF and private-public key pair using.
Can anyone please explain me how to use custom keys for MCUBoot, I added below config in /child_image/mcuboot...
Hi all
We are using ztest in our project because it works nicely together with twister, Zephyr's test runner tool. We need to have the ability to mock modules. For this...
Hi Team
we have NR52833 ,NRF52 these boards Serial no : 10001208 , 10001220
we use these devices in wipro BQTF as reference devices and not for any production. We are...
Hi
I read this Q&A: How to configure the P0.00 and P0.01 pins as GPIO , which is similar to my question. There are some things I did not get from that section:
"Physically...
Hi there, I am trying to do a blocking simple ADC measurement in using NRFX drivers in a threaded context, however when I build I get the following error:
gen_isr_tables...
Hi,
I am using nRF9160DK v0.9.0 with Cellular Monitor 2.4.0, and I have flashed AssetTracker2 via the "Program device" button.
Although asset tracker works fine uploafing...
Hi,
Using the nrf Connect Programmamer v4.2.0, I get the following error when connecting to J-Link on some of my custom boards (about 30%):
When I run nrfjprog...
I am attempting to enter a sleep state (System Off) with a wakeup button . I set all of my GPIO pins to the default config except for my wake up, configure the appropriate...
Hi
I am unable to get the Guiconfg to work in lesson 1 exercise 2 of the nRF Connect SDK Intermediate course.
I have attached snap shots of the output when I try to run...
I'm using the custom board of nrf 5340 with 7002.
When I run the sample project of Hello World, the current is about 90 ma,
and I run the sample project of WI-FI Scan...
We are going into sleep mode for the processor. We are using Zephyr and sdk 2.3. We also are keeping a running count of seconds and synching that once a day with a modem....
Hello,
I'm working on a product using the nRF9160 and facing challenges with poor LTE signal strength, leading to significant power drain when the device goes offline. I...
I was pairing using nRF connect app via mobile phone and I noticed that there's a check mark which says "PIN contains letters or symbols":
Is there a pairing method which...
