When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
I'm trying to test out the boot loader using the blinky sample. However if I add the following to prj.conf:
CONFIG_SECURE_BOOT=y
CONFIG_BOOTLOADER_MCUBOOT=y
I'm getting...
"SES > File > Open nRF Connect SDK Project..." does not seem to include a thread aware script for Zephyr. Is there a provided script for this somewhere? If not is there a...
Hello,
I would like to use a single COMP I/O pin to compare the pin voltage to multiple references during run-time.
To do this, I was planning on initializing the COMP...
With SDK For Mesh v5.0.0 the mesh_stack_power_down() was actually implemented but there is a bug that will disabled the proxy permanently.
For some unknown reason the mesh_stack_power_down...
Trying out the Sensor Model supplied with SDK For Mesh v5.0.0 raise a few concerns.
The way sensor_initialize() is made requires all supported PropertyId helper functions...
Hello For my application (which is based on the ble_thread_dyn_mtd_coap_cli example), I would like to be able to send a file (for an update) using bluetooth. To do this, I...
Hi, I have been studying a lot of issues reported here about leaving network and joining another. The most common answer is to use zb_bdb_reset_via_local_action(0); But when...
Hello,
I am using nRF52833, nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 and SEGGER Embedded Studio for ARM 5.34.
I have imported the ble_zigbee_dynamic_door_lock_nus...
Hello,
I am looking at using the nRF52805 in a new design, but I am worried about the 0201 and 0402 components that are recommended. Currently, my company manufactures our...
Hi,
I am evaluating Zephyr mesh and implemented two timers; one triggers at every 2 mS, the other triggers at every 500 uS.
I put a code in both timers' events to toggle...
Hi, Our platform is NRF-52833 Our project use RS485 bus (nordic's uart + a 485 chip) to communicate with other device. And we choose the libuarte to be the uart handler to...
Hi,
In the nRF_SDK_for_Thread_and_Zigbee_v4.1.0, in examples/thread/NCP/radio folder, there is no option for compiling the firmware for PCA10059.
I want to run RCP firmware...
Hello guys,
I'm trying to interface ds18b20 temperature probe and I'm using this code , In termite its showing output as -0.062500 I don't know why can anyone tell what...
Hello,
I'm using NCS 1.4.99 with a nRF5340DK and want to use the hardware CS of the SPI and also use BLE.
Here is a simple code that work on a nRF5340PDK but only work...
Hi All,
I was just reading the white paper on RF testing guidelines, and I noticed several times there have been mentions of "nRF Performance Instructions" for each of...
