Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hi,
I have a device that throughout the uart data to ble,recently I find a problem that in the case of weak signals,the data sequence is out of order.
Here is the question...
Hi,
I am trying to run the sensor example as provided in the Mesh SDK. I am getting the log as mentioned:
13691970>, main.c, 475, mocked motion sensed = 0% <t: 13691973...
Hi there,
I'm using the softdevice sd_ecb_block_encrypt to encrypt my 16byte block data as follows:
When my data buffer is filled, it called aes_encrypt(),
void aes_encrypt...
Hi Nordic,
I are working on battery operated device.
Need to measure battery percentage using ADC.
Let me know how can we select range of 0-100% for battery voltage...
Hello,
How do you flash custom firmware into the Nordic Thingy 52? The Thingy doesn’t reflect changes that I make to the firmware files and instead just turns off the...
I'm trying to find an example of how to properly buffer sensor readings between connections, and then transmitting the buffer on connection.
Is this just done via the user...
Hi,
I have developed a piece of software that only uses the GPIOs on the APP core to evaluate a sensor. The software worked on the development board processor so I made...
Hi support team,
In my case, i want to auto disconnect to ble central after some minutes with no message transfered, so i create an timmer and set event compare and clear...
We are developing a beacon with nrf52810. We test ble_app_beacon example and a modified example( the difference is, advertising packets are connectable to be applicable in...
I've configured UART2 on the nRF9160 to connect to a nRF52840. The nRF52840 generates a payload and sends it over to the nRF91. The payload size during testing was 65 bytes...
Hello,
I am developing using nrf2840 PDK, SDK v17.0.0, S140
I have made two services, one is to control the led blinking rate via nrf connect android app and the other...
Hi,
Is it possible to have dual transport for DFU (UART and OTA)?
I read this in the forum: https://devzone.nordicsemi.com/f/nordic-q-a/28118/multiple-dfu-transports ...
I have nRF52840 as the central and nRF52832 as the devices. I have the device names as TELCO_456, TELCO_457, TELCO_458 in the connectable advertisement packet. I have disabled...
I am trying to capture sniffer logs for a custom BLE peripheral using nRF51 dongle and Wireshark. I am following this guide here to install the Sniffer tool in Wireshark....
>I will start by prefacing that I'm not by any means an engineer and my only knowledge with BLE/embedded systems comes from curiosity, side projects and trial/error<
Story...
