I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I am developing a windows deskop application for BLE devices.
which laungage is the prefered for this type of Desktop application having predefined libraries..
Nordic...
We have an application running on a custom board with the following configuration:
nrf52832
SDK v12.3
Softdevice S132 v3.1.0 and S332 v2.0.0 (different variants of PCB...
Hi, I am using nRF51822 now,SDK11.0, how to let the peripheral open the peer's notification, My original design uses DA14580, Android APP can receive messages when the peer...
hello .
i am trying to open driver in the advertising.py example pc-ble-driver-py-master
driver.open() and this line throw exception
if err_code != expected: raise NordicSemiException...
It seems nordic devices can not be programmed without certain segger software.
In order to set up my toolchain, I had to install SEGGER Embedded Studio IDE (although i dont...
I have seen nordic contains QDID 111537 for mesh profile subsystems. Is this profile subsystem includes the Mesh Model or nordic have a plan to get Mesh Model QDID seperately...
Hi.
I'd like to disable retransmission in my Thread application built with SDK for Thread and Zigbee 1.0. I followed the instructions from Infocenter "Building the latest...
Hi @all
I'm searching for a nRF905 breakout board for the 868Mhz band. All I can find is nRF905 boards for 433Mhz (e.g. rfinchina or freqchina). Anyone tips where I can...
I'm trying to pair a Nordic SDK15 central to a non Nordic peripheral ( BLE 4.0)
I have no IO for passkeys
I'm testing by pairing Master control panel ( is it BLE 4.2?...
Hello team,
Having a bit of an issue. The link for the S140 SoftDevice results in an "Access Denied" page.
Origination Page >> https://www.nordicsemi.com/eng/Products...
Hi Everyone
I am able to configure BLE on the template project and it is sending data from nrf52840 to BLE nrfconnect app using the function nrf_ble_data_send() .
However...
HI All,
I am trying to upgrade sdk v11 to sdk v13 in my project and after compilation i am facing Linker Error as mentioned below.
binaries/app/SmartTag2/dfuFlash.c.o...
