I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
I have used NRF52840 and SDK 13.0.0. Module SPIM.
Library does not support buffer size more then 8 bit.
But I try write to register TXD.MAXCNT and I can't write value more...
Hi
I'm interfacing MMA8452Q with nrf51822 using TWI all read-write function working fine but when I try to read acceleration data nrf_drv_twi_rx & nrf_drv_twi_tx function...
I am porting our sdk 8 based firmware for the sdk 11. Now the code crashes at the code below:
err_code = sd_ble_gap_device_name_set(&sec_mode,
(const uint8_t *)name,...
We followed the instructions for the beacon example for nrf 52 dk.
Multiple attempts to change and reset the board, there was no change in the ad packet.
Can someone...
I'm using the nRF52832 chip without an external crystal. I configured it to use the internal RC with:
nrf_clock_lf_cfg_t clock_lf_cfg;
clock_lf_cfg.source = NRF_CLOCK_LF_SRC_RC;...
Hi,
I have tested ble_app_hids_keyboard for using whitelist.I find that this example is bond+whitelist. If bonded, the peer address will be added into whitelist. But when...
Hi,
I test Whitelist function in the example ble_app_hids_keyboard_pca10040_s132 using SDK12.2.0.
I donnot understand the code in "case BLE_ADV_EVT_WHITELIST_REQUEST:" located...
Hi all,
I have some problems with GPIO Interrupts.
I'm using nrf52832, s132 and sdk 12.2
The error is totally random so I don't know why is generated. The case is...
Hi,
We are using the Secure DFU from SDK 12.2, with SD132 3.1.0, on a PCA10040.
As a DFU controller, we use a PCA10031 with a SD130 2.0.1 and a project derived from the...
Hello,
We are migrating from IAR 760 to IAR 8.10 compiler does not produce the same assembly for the SDK12 inline function nrf_delay_us.
The original C Function is :
...
Hi, i am working on RTLS project. In beacons i want to enable DFU service using SDK 13.0. But I could'nt find a gothrough process to do the same. Please give me some link...
I am using S132 4.0.2 and SDK 13, and I have theese questions:
I have an application where BLE node establishes multiple concurrent connections (several as central...
Hello,
I'm having systematically an HardFault interrupt ~10 seconds after calling sd_soft_device_enable(NULL, &fault_handler);
This occurs on my bootloader code, but...
