I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I am not able to connect Garmin Edge or SimulANT to nRF51-DK. Neither sensor nor receiver seems to work. Just looks like there is no RF.
Examples tried:
power_only_sensor...
Dear Sir,
Here I test the ble_peripheral example "ble_app_uart" (Softdevice 8.0) with Kail MDK ARM 5.20 environemt on the PAC10028A board.
I found it's not stable and...
Hi,
I'm having trouble increasing frequency of data TX using ble_app_hrs example on PCA10028.
I tried to increase the TX frequency of heartrate data to 100ms by configuring...
It seems that the nRF52 Development Kit mis-handles extended hex records. If it has type "04" records (extended linear address), it works OK, but if it has type "02" records...
We have an optical measurement system where we need to pulse LED and sample a phototransistor precisely during the LED pulse. The rate of sampling is 1 kHz and we plan to...
HI i need help in sending a data value of 700+ continuously
1)May i know how should i format my data packet to suit the current 20 bytes of data sent through BLE
2)Is...
Hi,
I am working on application in which I want to send 1000 or more samples using SAADC and BLE over standard master control panel APP of Nordic. For sampling analog data...
I'm trying to fully understand how DFU works and am going through the nRF5 SDK v11.0.0 example bootloader ( dfu_dual_bank_ble_s132_pca10040 ) and app ( ble_app_hrs_s132_with_dfu_pca10040...
[summary]
When I update app by Keil μVision, RAM setting is reflected correctly, but when I update app on OTA, RAM setting change is not reflected.
[condition]
Old...
Im trying to read flash memory ( N25Q032 ) identifier using SPI (NRF52) but then eveytime I try to read a register, the output is always zero, I tested with oscilloscope and...
Hi,
I'm using the nRF Dongle for sniffing.
Apparently there are many problems with the sniffer application.
First of all, the CTRL+R command for downloading the FW...
Hi!
I am trying to modify the ble_app_gls example from the 8.0.0 SDK and am running into some issues. I am trying to add the nus service to this example and would like...
HI dear:
We have two questions to ask you：
1、Can we customize two different BASE_UUID in the nrf52832 ? If we can,and how to do it,We can customize one BASE_UUID (128bit...
