Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I don't find the information in the nRF51822 documentations and in this forum.
How can I know that? Is there some register to check, or some hints to know that debug mode...
hi,
i am using the nrf51422 and trying the UART example ( in order to connect the nrf51422 and a stm32f4 using serial connection)
what i didn't understand is what does the...
I am using a nRF51822(pca10028) for current measurement. I had set up the devices as told in user guide. I am using SDK 11.0, softdevice s130 and default ble_app_pwr_profiling...
I am trying to make a custom BLE service and be able to do debug it with UART at the same time.
Just trying to print some UART messages at some points in the code.
However...
I have a couple of questions with the MCP.
Before knowing MCP, I've been connecting with my nrf51-DK with the nordic master control app installed in my smartphone. Opening...
I am doing burst transfers using exactly the code suggested here devzone.nordicsemi.com/.../
The problem is, the data is received three times by the receiver (three times...
Hi!
I question the use of Software Interrupts and especially SWI3.
I'm currently developing an
application on nRF51422 based on
SDK10.0.0 and SoftDevice S110
v8...
I know that it can be done and I have read the other posts. I'm still running on SDK8.0.0 with both a S110 and a S130. Using wireshark and the nordic sniffer firmware on a...
hello everybody,
I need to send some data on the value attached with the notification:
/**@brief Function for adding the notify Level characteristic.
*
* @param...
My application need more than one of the host in the same area, we will set difference pipe of each host, we want to know the area already exist which of the pipe. Then we...
Is there a way to avoid fees, and still use BLE? Do I need to change UUIDs or leave them be?
If not can the nrf51822 be used to just use the pure 2.4 ghz protocol and DFU...
If a BLE device using nRF51822 has a freuqency drift around 80kHz (BLE limit is 50kHz). All other measurement item like ICFT can pass the BLE spec. Will the performance of...
Hi, this is my very first post to this forum.
I just received my nRF51 DK, so I installed a lot of stuff. The blinky example is running fine.
A question about nRFgo Studio...
hi, i am going to make a simple PWM with SDK 6.0.0, nrf51822 and softdevice.
first, i use ble_app_uart example as a base code, because i need to BLE communication with...
