Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
On pca10028 dfu_dual_bank_ble_s110_pca10028 example works fine. First i programmed soft device s110 and then dfu dual bank example my board gets into dfu mode and i can upload...
Hi,
I'm trying to get the UART working, following the idea given in the Nordic Infocenter / nRF5 SDK Hardware Drivers / UART / Using the UART Driver.
I have downloaded...
The code below is transmitting data from device (mcu+BLE) to an open source BLE terminal :
void BLE_communication_device_to_app(void)
{
ble.updateCharacteristicValue...
nrf51822_sleep_and_timer.txt
Hi... I having tough time to make the sleep function to work when timer/RTC is running in the background of nRF51822. The attached text file...
i am new to android programming and bluetooth low energy interface . i am using nrf51dk nrf51422 chip . My android app is currently able to detect the bluetooth module but...
Hi,
We are using the nRF52 chip with other RF modules. Is there any ground restriction that we need to be aware of in our design so that there is no interference ?
...
I have written an application which transfers data from an nrf51822 device to a phone once a day. It currently uses notifications to transfer data, at 20 bytes per notification...
Hi,
I'm learning the BLE protocal these days, I didn't see the protocal say how may packages can send per connection event. Does it mean that the number of packages is...
Hi
Details:
I want To send 40 bytes from GATT Server.My Requirement is same as in this link .I have added the code snippet in this link in my code.When I am sending 20 Bytes...
Hi,
I would like to use the NFC capability of the nRF52 on a custom PCB, and I was wondering if the tag and connector used on the PCA10040 are for sale anywhere, I can't...
We want to design a setup for simultanious translation of up to 3 translators and up to 30 people receiving a translation.
Is it posible to setup a single transmitter, sending...
Hi everyone,
I am trying to monitor and measure the signal strenth variation by varying the positon of the developement kit NRF51 and i tried with the proximity example...
Hi,
I'm using v1.21 nRFgo. As programming 51series ,
(1)I want to know if the program check the hex file before the log dialog shows "programmed successful"?
(2)And...
I run nRF51 with S110 and advertising at least standard battery service. I can see my device in LightBlue scan window but in iOS Settings->Bluetooth it is not picked up. Which...
