I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Exercise 2 doesn't seem to work for SDK v2.6.1 with v2.6.1 toolchain. SDK v2.5.1 works though. What configuration or code changes do I need to make it work for v2.6.1?
Hello,
I was curious if there was a project that uses 2 Mbps BLE to connect two nrf52840s, preferably with the ability to change which BLE channels the devices use. I...
In our custom board, check flash write and read using sample (C:\ncs\v2.6.1\zephyr\samples\subsys\nvs) but showing following response. the same build working fine in nrf7002...
This issue is for a programming environment on a macBookPro.
I finally get the system tamed and got to the point of testing the various sample apps provided. I wasted a...
1.Created a composite device for CDC and MicPhone. When the registration of mic SOF is interrupted, the device may not recognize the issue
ret = app_usbd_audio_sof_interrupt_register...
I would like to develop DTM and normal BLE stack operation in single firmware by NCS. Basically i will check a GPIO, go DTM test mode if GPIO short to High, go normal BLE...
Hi,
I'm evaluating the LE audio application to check the capability of using the Coded PHY for transmitting audio.
According to this page, LE Isochronous Channels: Configurations...
Please find below my config for handling Interrupt calls.
I've tested on another sensor dev board that the sensor I use is properly set up and is sending INT1 and INT2....
Hi everyone,
I am working with nRF52832, I am trying to implement the Zephyr Modbus client example onto it, but i keep receiving the following errors.
There is this...
Hello everyone
I'm trying to connect 2 board nRF52-DK (PCA10040) via modbus RTU using zephyr example (client and master in 2 different board).
I'm using visual studio...
I just installed the toolchain (2.6.1) and SDK (main) from scratch, and I'm not able to build the Serial LTE Modem and Asset Tracker application. I receive an error during...
Hi There,
Are the GPIO levels high impedance when the system is in off mode? Can you give information about their status? For example, one pin of the device is configured...
Hi there,
I'm on Ubuntu 22.04.2, 6.5.0-41-generic kernel.
I've been trying to setup the nRF connect toolchains & SDK through VSCode. Things seem to install fine, but when...
Hi,
I have a solution that every 15 minutes needs to perform a WiFi Scan and save the BSSIDs that it finds. Sometimes it will find the maximum number set and will complete...
