Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello!
We are using a custom nRF9160 board with 3 differential ADC channels. The differential voltage is measured across two resistors, with the center voltage (normally...
Nordic Team,
I have a question regarding RTC1 with regards to app_timer2.c
My Setup: nRF52833 - PCA10100 Development Board nRF SDK v17.1.0 s140_nrf52_7.2.0
What am I...
Hi, I'm working with just one NRF5340 audio DK and I saw this ticket where it was commented that it is possible to reduce the use of 2 NRF5340 audio DK's to just 1 using a...
Hi,
I have one central and one peripheral devices running. Currently I run a scanning filter on Central side and connected to the peripheral with desired name.
But now...
I was trying to follow the instructions at https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf52_gs.html#connecting-to-the-application for testing my nrf52840...
Hi,
Using Windows 10 and SES
SEGGER Embedded Studio for ARM Release 6.34a Build 2022083102.51023 Windows x64 2014-2022 SEGGER Microcontroller GmbH 1997-2022 Rowley Associates...
Hi all,
I want to ON and OFF advertise manually
My code working steps
1) (APP_ADV_DURATION 3000 ) after this seconds over
2) It hits on_adv_evt() function in this...
Hi All,
I am using asset_tracker example V1.8.0, it's working fine with nrf9160DK. I am able to see the data on nrf cloud.
The purpose of testing this board was to debug...
I am working on two devices, a peripheral and a central. The peripheral is custom hardware. The central is being run on a Rigado BMD-300 series evaluation kit. I'm using Segger...
Hi,
Perhaps this question is too basic, but I haven't been able to find this anywhere.
I've followed this tutorial successfully with an nRF52832 DK:
However, I'm missing...
Hello,
I wanted to create an SPI shell, similar to what is available for I²C. I am therefore trying to create a generic SPI device in the devicetree:
Somehow I am...
Hello,
We use nRF52840(0dBm)+nRF21540(Dec6).
In the case of using nRF52840+nRF21540, tx spurious emissions occurs severely in the nRF21540 output.
FEM(nRF21540) output...
Hi.
I am developing a custom board using the NRF52840. The mcu needs to connect to a modem and a gnss module. Both modules will communicate with the mcu over UART
I'm...
I'm working on a prototype that has 8 BLE sensor nodes that are powered by coin cells and placed on different parts of a human body.
The host node is the main processing...
