Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I am discovering the nrf52 software with the Segger Embedded Studio environment. I have developed an application derived of the ble_app_uart example.
I have many events...
Hello,
I am getting the following error in Segger Embedded Studio v5.60
SEGGER Embedded Studio for ARM Release 5.60 Build 2021081102.47262 Nordic Edition Windows x64 ...
Hello,
I changed saadc.zip for my application needs
and would like to plot the incoming serial data from ADC as asked in
For time evaluation I would like to have...
Hi
We would like to test the “Carrier frequency offset” of the PCBA during production. Like the BT SIG test: RFPHY/TRM/BV-06-C [Carrier frequency offset and drift, uncoded...
nRF5 SDK, SD140 7.2.0
I am running a bluetooth application that also has OTA DFU capabililty via bluetooth. In my normal application I use a timer to advertise for exactly...
I need to set the SPI Mode NRF_DRV_SPI_MODE_0 for a 2nd chip (on the same SCK/MISO/MOSI) to NRF_DRV_SPI_MODE_1.The chipselect is handle by the application.
I can't do the...
Hello,
Is it possible to clone services of peripheral device connected with "Bluetooth Low Energy Standalone v4.0.0" PC application? I see it is possible in "nRF Connect...
nRF52840
NCS 1.9.1
I have successfully downloaded app_update.bin to flash and rebooted. MCUBOOT copies the new application correctly and it runs fine.
The boot process...
I opened an issue on GitHub, but the NRF Connect iOS repo has not been updated recently. Here is the link: https://github.com/NordicSemiconductor/IOS-nRF-Connect/issues/118...
Hi guys.
I'm using the development board NFR52840DK and I modified the sample in zephyr\samples\boards\nrf\nrfx to use twp buttons, sw0 and sw1.
The sw0 button reset a...
Hi,
I want to use my PC to send some message to dongle via USB, then the dongle send them to certain device via BLE.
If there is a sample that allows PC interacting with...
Hello,
I have tried running Blinky example with some Low Power directives in the code without success. I came here for help then.
The current consumption used by the example...
Hi All,
I am trying to port my current SES project (s140) from nrf52833 to nrf52832. My nrf52832 is spec'd at 512kb flash and 64kb RAM. Any help would be much appreciated...
Hi,
Trying to evaluate the nRF52840DK with Matter examples but none of them seem to compile.
Following error is the result
Building light_switch west build --build-dir...
