I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I use the zephyr version 3.0.9,when i build the hci_rpmsg project,it have serial error.then i chnange the onfigruation by add some new definition.
I add some configurations...
Hi,
What macro should be used in the bt_data ad struct in order to advertise a custom 128 bit UUID? I have tried the following: BT_UUID_128_ENCODE(BT_UUID_CUSTOM_SERVICE...
The Trace Collector V2 preview (v0.3.5), seems not longer working. (It was working nice before with the mfw 1.3.2.)
Unfortunately, I'm not sure, which of the updates of...
Hi there,
I was using app_uart_put to print out data from a nRF52, but now I need use printf to use AT commands more easily(more readable) instead the working around app_uart_put...
I am going through the Nordic tutorial Creating Matter device ( developer.nordicsemi.com/.../ug_matter_gs_adding_clusters.html ) but I am getting errors during the build that...
It took me a few days to determine this issue, so I wanted to share it with the community if you come across this issue. If your pairing process is not sharing the IRK/ Resolvable...
Hello,
Our production device is having issues with the BLE connection only identified with the Samsung S20+ model currently. We are using custom services for our phone App...
Hi,
I am working with nrf52840 development kit and raspberry pi 3b module.
Using raspberry pi module i am able to scan and connect to nrf52840 development kit.
Now...
Hallo,
I am currently trying to debug the Matter samples on the NRF5340 DK. They all work fine, but I have a problem with the "Thread Viewer" in VS Code while debugging...
I have cypress ble module that generates carrier with PRBS9 modulation and GFSK on 2408MHz. As a receiver I use nrf52 Dongle and nrf52 DK board. In RSSI viewer I can see signal...
Hello Before we just have to overwrite shouldAutoConnect to enable an automatic reconnection Is autoconnect supported on Android NRF toolbox 3.1.3 (kotlin implementation)...
Hello,
In order to reduce the consumption, I remove some sensors (physically from the board).
Should I change the SW ? Is there any discovery state required that should...
Hi Nordic,
1. I am using bl653_dvk board and (C:\ncs\v2.1.0-rc2\zephyr\samples\drivers\uart\echo_bot) is using for my sample
2. Here is i need to communicate with both...
Good day
sorry if it's not clear, it's a rare problem and I have difficulties to explain it but here goes:
I Have two boards - PCA10056 from nordic and nrf52840 Feather...
