Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
The CAN controller MCP2515 should be connected to the Nordic DK NRF5340 by the SPI interface.
Communicate to Arduino uno
We were trying with CAN sample given
But this...
Hello,
I've tried to request the location via AGPS/PGPS via Location sample in SDK 1.8 but it seems that location is only working with the Cellular method.
I've tried...
Hello there, I am new to your product, and I am trying to understand your library logic and hierarchy. Right now I am trying to figure out what all of these prefix (such as...
Hi, I want to use an NRF52805 with a voltage to frequency detector. If I understand the datasheet, there is one timer/counter and RTC on that chip. Is it possible to set the...
Hello,
How do I deactivate/activate a SDA/SCL line?
I perform a test on an Icarus board with a VL53L1X sensor, everything works fine.
However, in idle/sleep mode, whether...
Hi,
I am unable to view the output of the prink statement on the SES debug terminal. I'm a beginner so please bear with my lack of knowledge.
Should I be looking for the...
I am trying to adapt the zigbee light_bulb sample to run on nrf52840-Dongle which does not have a QSPI flash chip. I see that it crashes unexpectedly during settings_subsys_init...
Hello,
We have product with nRF52811 as Bluetooth receiver and ESP32 as WiFi IC. The ICs have separate antennas, and nRF52811 has LNA with +12 dBm gain connected to antenna...
https://github.com/project-chip/connectedhomeip/blob/master/docs/guides/nrfconnect_examples_cli.md
uart:~$ clear date device devmem flash help history hwinfo kernel nrf_clock_control...
I have loaded up the altium design and can see the pad and via sizes used.
The drill size for the in pad via is very small (0.15mm) which will increase pcb costs and also...
*** Booting Zephyr OS build v2.7.99-ncs1 ***
nrf52840dk_nrf52840 system off demo Retained data not supported Busy-wait 2 s Busy-wait 2 s with UART off Sleep 2 s Sleep 2...
Hi,
Installed the toolchain, installed VS Code, and I think its all linked, but when I try to run even the most basic hello world program it just keeps throwing this error...
hi support team,
i am confused about "advertising extentions" part;
Inforcentor shows example for " Cycling Speed and Cadence Application" only support S132 and S140,...
Hi,
I am developing my own vendor specific USB device with 2 interfaces (data and debug) and 2 endpoints(in and out) each. I based my class on the cdc_acm class.
So far...
Hello ,
hi everyone, in my project i am using internal RTC timer for calendar concept like when i set a target time via UART for every day the internal RTC timer should...
