Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
We have a custom software for our custom board. And would like to investigate a little in the AT commands going to the modem and the responses
is there a config...
I am using Connect SDK v1.7.1 and Ozone v3.26b. When I click "Debug with Ozone" in VS Code, I receive the following warning in the Ozone console:
I am able to correct...
Hello,
While developing the device, I found that the SAADC module on the NRF52833 incorrectly measures the voltage on the NRF_SAADC_INPUT_VDD channel if you set the REGOUT0...
Hi,
We have a device in production based on nrf52840 which uses UARTE to TX/RX data to/from a washing machine and in paralel communicates with a Phone App via BLE.
SD...
Hi,
I am using nRF5340 Audio DK. I have 3 kits currently and I have programmed one as a headset and the other two as gateways.
I would like to use the whitelist so that...
I think it'd be nice if there was a connect button like this.
but my device appear one button.
I think the multi-link function should be possible to solve this problem...
Is there a working example with using gpio_dt_spec for accessing gpios?
I used the code provided from https://docs.zephyrproject.org/latest/reference/peripherals/gpio.html#c...
Hello, by usingnrf52832 DK and testing some examples i found out that the example peripheral UART was not going like I wanted to do. He is going to sleep mode after 3 minutes...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v1.0.1%2Fmd_doc_getting_started_how_to_models.html
Linkte verilen yönergeleri takip ederek...
Hi all, I discovered that if I get BLE_GAP_SEC_STATUS_AUTH_REQ while pairing, the device is basically useless until a new reset. I would be extremely grateful for some help...
Hi All,
I have a project which uses the zephyr shell, but I can reproduce the issue with zephyr/samples/subsys/shell/shell_module or any other sample making use of the UART...
uint32_t address = XIP_ADDRESS + addr ;
uint8_t * p_data = ( uint8_t * ) address ;
for ( int i = 0 ; i < len ; i ++ )
{
data [ i ] = p_data [ i ] ;
} The Pin of QSPI...
Hello,
I recently installed the VSCode Extension for nRF Connect and I am experiencing, what seems to me, strange behaviour.
Here's the steps:
I create a project from...
