Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
I noticed that if you send AT+CFUN=1 then AT+CFUN=4 more than 30 times in an hour the modem stops registering until the hour passes? Is this by design?
Kind regards...
Hi,
I have built and flashed the "peripheral_uart" example on the nrf52833dk_nrf52833 from nrfconnect sdk v1.5.0. When I build using the prj_minimal.conf file, everything...
Is it possible to manually delete/inject bonding keys when BLE connecting to device with using Nrf52 and pc-ble-driver.py? I would need to execute following scenario:
1...
I have seen a compatibility matrix for nRF52840 SoC at the link below:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52840%2FCOMP%2Fnrf52840%2Fnrf52840_comp_matrix...
Dear, manager.
Hi,
I am currently testing the use of TWI and BLE together.
However, Data (24bit) is received and read through TWI every 4ms. BLE is only initialized...
Hello,
We are evaluating SDK 17.0.2 USB MSC example.
If we connect the PCA10056 board to USB the Windows make System Volume Information folder,
so if we don't make safely...
Development environment SDK 15.3.0
I am working on overturning the saadc project based on ble_app_uart.
The input frequency is 50~2k Hz.
Terminal and debug monitor...
Hello I'd like to output two PWM alternately. Using the timer, PWM1 and PWM2 alternate outputs every 5 seconds. And I want to change duty cycle according to adc value.
...
hello,
i am using nrf52840 in our customised board and trying to interface it with GDEW0213Z16 2.13 inch display which uses spi communication i have added the necessary...
Hi,
Currently, nRF91 supports only one MIPI RFFE-controlled device. In our solution, we would like to have two MIPI devices - one pair of LTE switches as in Thingy:91 for...
Hi ,
Technical Environment details:
nRF Connect SDK
segger Embedded Studio
nRF5340 DK board
1. I have enabled immutable bootloader and MCUboot bootloader.
...
Hello,
Per the datasheet, VDD_GPIO must be applied after VDD has been applied. Is there a minimum or maximum time?
For example, can VDD_GPIO be turned on 1 second after...
Hi,
I am evaluating nRF5340 for using it in a smart lock product with high security. I had evaluated nRF52840 before this
and was impressed with the integration that the...
I started with the ncs-display-ble-example which worked fine. Next I took the LVGL lv_demo_widget, ran it in the simulator using visual studio 2019 where it ran fine. Then...
