Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Is there a way to change the Thread SDK example program (\examples\thread\ncp\ftd\uart) baud from 115200 to a higher 460800? If so, what steps are needed to make this change...
With SDK For Mesh v5.0.0 the replay cache is saved to flash using MESH_CONFIG_STRATEGY_ON_POWER_DOWN. In mesh_config_load() a check is made to ensure that there is enough...
Hi,
I'm working on porting BG95 to nrf52 sdk, it'd be a lot helpful if I can get a head start with some open source implementation(AT parser libraries, drivers porting etc...
Hi,
In the Product Specification for nrf52840 it´s written that setting CONFIG (0x50C) register to Pause (0) would pause the watchdog while the cpu is halted by a debugger...
nrf52840 with SDK15
I am trying to update 3 characteristics if the correct value is written to an authenticated read write characteristic. Actually all of my characteristics...
I'm trying to create a simple point to point link using the nRF24L01+ with a new non-arduino microcomputer. I've searched the internet for example Python programs but only...
Hi,
I would like to double check with you if 9-pin cortex-M adapter board for Jlink can be used and connected to PPK P21 connector : https://www.segger.com/products/debug...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using internal flash one of the sector with start address of 0xfc000.
We have written...
Hello, we are having a low occurrence issue when attempting to write some data in NVM using fstorage.
We are using a nRF52832 as a BLE peripheral using SDK15.2.0 and SoftDevice...
Nordic colleagues,
We just received our nRF 52840 DK and are attempting to install the nRF Sniffer application to use with Wireshark. We were able to program the DK with...
Are there any plans to expose a raw packet interface for the nrf9160? And ideally forwarded via an async serial port, perhaps as an option for the SLM application? i.e. without...
Hello,
I have a problem of reading GPS options for "NRF_SO_GNSS_POWER_SAVE_MODE"
This is the code:
I always get -1, and errno value 22. This function works for ...
Problems encountered in nrf51822 software development: When burning the program to the microcontroller, I used the Bluetooth serial port service to send the collected adc...
I'm working on a prototype currently using the nRF52840 dongle. I've used the ble_app_blinky as a basic, and added some custom code to it. The goal is to use BLE in the end...
Hello everyone,
My empte memory is displayed as EE instead of FF after i cleared the memory.
I use commandpromt to check memory:
nrfjprog --qspicustominit --memrd...
