I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi guys,
I have already created some code in a peripheral folder inside nrf5 SDK documentation related to temperature readings and the way how to save the data in the flash...
Hi all,
i am getting values properly, if i set 250 samples per second. but if i set 1000 samples (1ms), i can not get values after some moments. it is showing time out error...
Hi,
In preparation for FOTA which would double the flash space requirement, I noticed the Region Size for FLASH is only 429568 and I would have assumed it was the 1MB advertised...
I am trying to connect my thingy91 and preform an MCUBoot. This is not working and i get the following error code: Errorcode: CouldNotCallFunction (0x9) Lowlevel error: INVALID_OPERATION...
Excuse me, I use BSP_EVENT_KEY_0 to get into the sleep mode, however, it will go to the NRF_BREAKPOINT_COND and then reset the device;.
case BSP_EVENT_KEY_0:
SEGGER_RTT_printf...
I have developed data loggers based on nrf52840,it uses nus service,max payload is of 240 bytes,the device stores 30kb data in a spi memory.we have a custom built android...
Dear community, as already mentioned here https://devzone.nordicsemi.com/f/nordic-q-a/30622/nrf_cal_set_time-setting-issue-for-2100-year/121167 Im wondering how do you deal...
Hello. I need to calculate the RSSI value from the module nRF9160. I am using the nRF9160 DK 0.8.2. From the AT reference guide, there are two commands: AT+CESQ and AT+CSQ...
The new Bluetooth specification 5.2 will support transmission of audio data in a so called isosynchronous burst mode to external, BLE capable speakers, opening up a long asked...
Hi,
We are having some issues with the values obtained via ADC readings. We have a few designs using the nRF52840 where the analog reads from sensors are not stable. To...
Hi,
We used nRF52840 Dongle to receive BLE peripheral device 240Bytes notification. The connectivity that "Bluttooth low energy" (nRF connect) programmed can received 240Bytes...
Hi,
I am using NRF52810 controller, The power consumption of my board in SLEEP MODE is 200uA . According to datasheet the ideal current in sleep mode is 3 uA.
In advertising...
Hi,
I use SDK16 ble sec-bootloader and merged application image together followed by the guide of the website
unfortunalately , after flahsing fw_all_s140.hex to device...
Hello,
Question regarding GPS power consumption numbers in the nRF9160 data sheet (V2.0)
Section 5.2.1.16 GPS Current Consumption:
Are the current consumption numbers...
Hi,
I would used a RTC calendar (Years, month, day, hour, minute, second).
The smartphone connect to the nrf51822 and updates the date and time.
The nRF51822 must perform...
