Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I am wondering if I could have access to a mechanical drawing or 3D model of the N RF52840-DK . Does anyone know where I could find either of these?
Thanks,
Julia
I am trying to understand why my program is returning this error (NRF_ERROR_RESOURCES). I read through a lot of other posts in the devzone and tried replicating them, but...
My board is nRF52840 + S140 + nRF5_SDK_15.2.0_9412b96, my configue as below picture and file "ywk_bsp_ble.c" .
When nRF Connect APP connect my device, it alway be disconnected...
Hello,
I am using nRF52832 (BT832 module designed by fanstel) based module for my application. we have developed customized PCB using the module. while evaluating the...
What chip supports Open Thread? SDK and softdevice versions supported?
We are in evaluation phase looking for potential radio manufacturers for an upcoming project.
Any...
I see similar posts, but no answer of this problem. I have similar code that work on my FW, but when I port it to my BSL, advertising is not working and when I look at return...
I am migrating from SDK11? to SDK15.3 and noticed nrf_drv_common.c is no longer available and has no replacement although nrfx_common seems to have replaced nrf_drv_common...
Hi, what are the (security) implications of running bootloader with #define NRF_BL_APP_CRC_CHECK_SKIPPED_ON_GPREGRET2 1 in production code? We use sdk15.0.0 with secure dfu...
Hi everyone,
I have an issue with power consuption. I work with the SDK15.2.0 and the SoftDevice S140 on a custom board.
I launch the ble_app_pwr_profiling example on...
I wasn't receiving any log messages while debugging the ble_app_uart_c example using SES so I enabled appropriate logging functions and set them to level 4 in config.h. Still...
We are using NRF_SDH_DISPATCH_MODEL_APPSH, and are generally very happy with it (especially for BLE events). However, I'm trying to retrofit error handling around complex...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I define the following macros in "Section Placement Macros".
Can I use these macro values in my...
When the boot loader calls the sd_mbr_command it does not get updated.
sd_mbr_command_t sd_mbr_cmd;
sd_mbr_cmd.command = SD_MBR_COMMAND_COPY_BL;
sd_mbr_cmd.params...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I recognize by default that the top address of the app is 0x26000. I want to change the top address...
I need to measure current of loads attached to NRF52832 using current transformer(CT).
I can use SAADC library to read ADC value. But to measure current I have to know the...
