Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I am trying to determine whether or not the SPI EasyDMA functionality of the nrf52840 supports double buffering in the sense that the DMA controller will switch buffers...
Hello, I have a problem with properly adding the Azure IoT SDK (C) into Segger IDE. Anyone already managed to get through that? My goal is to have Azure IoT Hub working with...
Hi, I'm attempting to use the nRF52832 Smart Remote 3 SDK for a project on an nRF52832. I wish to add Serial Output capability (for debugging purposes). I followed the example...
Hi,
I notice that inside the MESH SDK, "Friend" is actual a hex file from zephyr, which I cannot modify. My goal is to set a "Friend" to connect more than 1 LPN (low power...
Hello, community. I have a question about hardware and software setting for using 32Mhz.
(1) Software setting in sdk_config.h
#ifndef CLOCK_ENABLED #define CLOCK_ENABLED...
Hi, I'm searching a example project to do the qualifications test for my product. I'm using SDK 10, have you an example for this SDK? (in your site I found an example with...
Hello
I'm trying to maximize the throughput between a NRF52832 and iOS devices in both directions.
Currently, I seem to achieve about 400 Kbps from an iPhone 8 to the...
Hello, I Have been using your app Connection for Mobile to test my Heart Rate Monitor BLE, I am using also an Honor 9 Lite (Lineage OS 15.1).
The app Nrf find my monitor...
I would like to use the beacon example to send some manufacturer specific data over BLE.
I am using the nrf52DK , nRF5_SDK_14.2.0_17b948a and s132.
My question is other...
What's the fastest scanning settings for connecting to anywhere from 1 to 20 peripherals at a time? My peripherals are all advertising at 211.25ms. I won't be sending any...
Hi,
I am trying to use an SAADC converter to measure voltage in range from 0v to 3v5 but I cannot succeed. It is not possible to measure a voltage above 3V1. Well at least...
Hello, community.
I'm using NRF51822 SoC(256KB ROM, 32KB RAM) with S130 Softdevice.
I'd like to reduce the rom size and the ram size to decrease the production cost. ...
Hello,
I am using nRF52840 DK for bulding a bluetooth mesh. I would like to use JLink in board kit to flash and debug for other nrf chip.
How I can connect and configure...
Hi,
I'm using SDK 15.3. How do I connect a central (nrf53832) to another central (phone/laptop) using multilink central example? Its only connecting to other peripherals...
