Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
i am using latest version mesh sdk 3.1 .. i want to interface two boards and want to check the bidirectional using text message, example if client sending the hello message...
Hi,
How can I Understand why the nRF9160 is disconnecting from the network?
How can I read the modem trace bin file to understand whats going on with the modem ?
Hello,
Do you have a soft device that integrates both Bluetooth and USB on the nRF52840 ?
I want to program a firmware that uses both and I'm wondering if you have ready...
What changes are needed in SDK V15 sdk_config.h so nRF52832 can run on internal RC oscillator?
I am using the BLE UART example, nRF52832 with Soft device s132_nrf52_6.0...
I want to extend the list of known UUIDs with some custom definitions but I am unable to open the Open UUID definitions file.
I tried following the Adding UUID definitions...
When connected with RTT viewer, a pin reset with nrfjprog shows a J-Link Error popup saying:
J-Link currently uses target interface SWD while current debugger tries to select...
Hi!
I want to send heartbeat messages from 30 servers to 1 client/provisioner.
I can send _HEARTBEAT_PUBLICATION_SET to every server like OpCode = _HEARTBEAT_PUBLICATION_SET...
Hi，
I have searched the posts about how to send/receive more than 255 bytes ,SPI master EasyDMA mode , but still can not find the solution.
I want to know if a ArrayList...
Hi,
i am facing two issue in nRF9160 cellular application.
1.Asset tracker Application:
i loaded Asset tracker example firmware in nRF9160 eval. board. when i run this...
Hello,
I'm porting a project from SDK14.2.0 to SDK15.3.0. Now, all is compiling, i need to figure out why my project is triggering some exception. To help me, i would like...
I am a newbie with nRF Sniffer, which I have installed on one PCA10040 board. I am sniffing communications between a Samsung phone running nRF Connect and a second PCA10040...
Hi,
Here I am trying to use nRF52 DK single board to implement SPIM0(base address: 0x40003000) and SPIS1 (base address: 0x40004000) master and slave communication protocol...
Hello, It is my first time running FreeRTOS on NRF52 and I would really appreciate any help to figure out the root cause for the hard fault. I run a simple FreeRTOS application...
nRF52832_XXAA, S132 v5.0.1, SDK 14.0.0
We enable SoftDevice via nrf_sdh_enable_request(). We immediately assert nrf_sdh_is_enabled() so we know it worked. On the first...
I recently got a custom board manufactured using an NRF52840 with the TI AN043 antenna to find that everything worked except for the bluetooth antenna. So I'm here to seek...
