Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hey there!
I'm playing around with an nRF91 DK using the serial terminal app (the standard one which is programmed during the getting started guide) and am trying to make...
Hi there
So I want to make an application to send mqtt messages over wifi. I have tried to follow the devzone guide: to implement the mqtt api into my software (Mostly the...
While building my first blinky project using nrf connect on VS code it is showing following errors:
C:/ncs/v2.6.1/zephyr/scripts/kconfig/kconfig.py: C:/ncs/v2.6.1/blinky...
Hello,
How can I add serial SRAM or serial Flash to a Thingy:91?
On the nRF9160DK there is 64 Mb external Flash onboard but I assume there is no external Flash on the...
I want to decrypt some packets caught in LE Audio(Using the sample:nRF5340 Audio application), but need the link-key.
According to this case , I add these to prj.conf to...
Hello,
I am using uart with thingy:91 to communicate between nrf52 SoC and nrf91 SiP, i am able to receive data from nrf52 but when i try to send data to nrf52 SoC the function...
I integrated the sd card code into my main code in which the the wifi module (nrf5340 + nrf7002) receives uart data from a different device What I need to do is that whenever...
Hi!
I am using BLE Central sample of nordic connect sdk. Upon running it on nRF52832 it successfully scans for peripheral, and display its Random MAC address, is there any...
Hi,
I am using the non blocking TWI on the nrf 52840 with the following code:
The xfer is handled like this:
TWI config is
and
The twi_event_handler...
Hi, I have a FEM module connected with spi0 on an nrf5340 running Zigbee. without the FEM module, the range of the device is around 10 meters (specific environment, not free...
Hi,
we would like to provision TLS tags / certificates for cloud authentication over Segger RTT on a custom device. We are using the Golioth cloud with the Golioth Firmware...
Hi,
I am working on optimize the SPI timing for an NFC reader IC which connected to nRF52840, to minimize the read/write time as much as possible.
And I notice that...
Hello,
I am evaluating the Thingy 53 + nRF7002 EB for Wifi and Bluetooth scanning.
But depending on which power source I plug the devkit, the wifi interface doesn't set...
Hello,
I just bought a nRF52 DK board (PCA10040, 3.0.0, 3023.22, 1050315142 ). It has a N5340 MCU near the micro USB port, and on the other end, it has a N52832 MCU. I have...
