I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
Is it possible to get the device name - i.e the GAP_DEVICE_NAME - of an unprovisioned or provisioned device using a serial device and the interactive_pyaci? It would...
Hi everyone,
at the moment we are trying to upgrade our nRF9160 software form the SDK v1.8.0 to the newer version SDK2.0.0. The main issue of the migration is our UART implementation...
Hi,
I'm using NCS v2 and VSCode on a custom board, and the android nrf connect app.
The board which has an external crystal, which I am not trying to use, in favor of...
Hi,
I am migrating to use Advertising Sets, which require Extended Advertising, and I am seeing that the number of connections per-connectable-service is seemingly reduced...
Hi,
I have been successfully working with CoAP customized client/sever app for a custom dev board. This custom dev board was based on Minew MS88SF21 module. I have created...
Hi,
I create two extended adverts, one connectable and one none, (nRF Connect 2.0.0) using the following code:
This works great, but then i want to amend the data...
Hi, I have just started looking at integrating Matter in my devices and am looking to measure voltage. However, there is no cluster under the matter clusters that matches...
Hi,
There is a loose wire on our PDK, The right side is on the cap, but the left side is loose and not clear where it came from. Can you help?
Regards,
Peter
Hello everyone,
In my application, and in samples I have studied, the A-GPS data request starts with the NRF_MODEM_GNSS_EVT_AGPS_REQ event when the modem wakes up/is started...
I'm in the project in which we are trying to implement logging to file functionality to NRF5340 chip.
Following lines were added to config.proj file:
# experimental...
I am trying to write the code for motor controller. I am need to move motor to certain number of ticks based on the given input.
Currently I am using n20 motor for testing...
Looking through a lot of the examples there is a pattern like the following:
Where you capture the success of the function, and on a failure return 1. My main question...
Hi,
We noted in the errata (Issue 133) that the radio performance is significantly degraded if the QSPI is enabled. The suggested workarounds are to 1) lower Vdd to 1.7...
I was working on some project that time i got this error
-- Application: I:/edge-rtos-babelfish-v3/examples/blinky_starter_app -- Found Python3: C:/Users/40025637/software...
