I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi! We are trying to put in the same application for both GNSS( developer.nordicsemi.com/.../README.html) and NBIOT( developer.nordicsemi.com/.../README.html) .
The examples...
Hi，I have a question:
1.I use device_ get_ Binding ("UART_1") When UART1 is opened, ENXIO returns to 134. How do you solve this problem? For others, I used uart0, spi2,...
Hello everyone!
Please tell me if I can connect nRF21540 to a microcontroller using only 4 SPI pins (SCK, MOSI, MISO, CSN) and control it completely? At the same time I...
As the title describes, I am getting that error. I am using nrf sdk 17.1.0 on an nrf52840, developing in SES. I have enabled NRF_CRYPTO_ENABLED, NRF_CRYPTO_BACKEND_MBEDTLS_ENABLED...
Hello,
I am currently using Nordic border router image as suggested by Google open thread group as i am using NRF5 SDK examples (sleepy mqttsn-publish example to be precise...
Hi team,
I am using NRF52833 DK with PCA10100 on it and s140 soft device version..
I added service data in advertising_init() function in ble_app_uart example code ...
Hi,
I have used DFU to update my application and worked normally. Now I need to update the application which has be written in NOR flash.
Firstly, I will write the application...
Hi,
We are building the custom bootloader in Rust,
Therefore want to define the non secure memory region.
Need to know exact steps to define the Non secure memory regions...
hi team,
i am using Microsoft Windows 10 Enterprise OS and Segger 5.40 version IDE.
i am using nrf52840 device in my project along with nrf5_SDK for uart peripheral check...
Hi,
In one of the example( zephyr / net / dns_resolve.h ) In this function description "dns_get_addr_info()" mentioned like below,
@details This function can be used to...
Now I've made a board using 52833 and downloaded the 's140_nrf52_7.0.1_softdevice', 'bootloader', 'settings' into 52833.
I use SD_POWER_DCDC_MODE_SET() to enable DCDC in...
Hi
I implemented in the function call in the SDK bootloader on a nRF52840 the BLE MAC address with the following function call:
The type BLE_GAP_AD_TYPE_LE_BLUETOOTH_DEVICE_ADDRESS...
hi Team,
i am using Microsoft Windows 10 Enterprise OS and segger 5.40.
i am using nrf52840 device in my project along with nrf5_SDK.
i compiled pwm code with different...
Hello, I am working on jumping from the app to the bootloader to do a firmware update from there. If I don't have any application firmware on the nRF, the DFU also works without...
